Redundant Power Supply Module GE Fanuc IC693ALG223 PLC Module INPUT
ANALOG 16 PT CURRENT
Number of Channels 1 to 16 selectable; single ended
Input Current Ranges 0 to 20 mA, 4 to 20 mA and 4 to 20 mA Enhanced (selectable per
channel)
Calibration
Factory calibrated to:
4 µA per count on 4 to 20 mA range
5 µA per count on 0 to 20 mA and 4 to 20 mA Enhanced range
Update Rate 13 msec (all 16 channels)
Resolution at 4-20 mA 4 µA (4 µA/bit)
Resolution at 0-20 mA 5 µA (5 µA/bit)
Resolution at 4-20 mA Enhanced 5 µA (5 µA/bit)
Absolute Accuracy
± 0.5% of full scale over specified operating temperature range
Linearity
< 1 LSB from 4 to 20 mA (4 to 20 mA range) < 1 LSB from 100
µA to 20 mA (0 to 20 mA and 4 to 20 mA Enhanced ranges)
Isolation 1500 volts between field side and logic side
Common Mode Voltage 0 volts (single-ended channels)
Cross-Channel Rejection> 80 db from DC to 1 kHz
Cross-Channel Rejection 80 db from DC to 1 kHz Input Impedance
Input Impedance 250 ohms
Input Low Pass Filter Response 19 Hz
External Supply Voltage Range 20 to 30 VDC
External Supply Voltage Ripple 10%
Analog Current Input - 16 Channel
IC693ALG223
The 16-Channel Analog Current Input module provides up to 16
single-ended input channels, each
capable of converting an analog input signal to a digital value for
use as required by your
application. This module provides three input ranges:
4 to 20 mA
0 to 20 mA
4 to 20 mA Enhanced
OTHER SUPERIOR PRODUCTS
Yasakawa Motor, Driver SG- | Mitsubishi Motor HC-,HA- |
Westinghouse Modules 1C-,5X- | Emerson VE-,KJ- |
Honeywell TC-,TK- | GE Modules IC - |
Fanuc motor A0- | Yokogawa transmitter EJA- |
Similar Products
IC697ACC621
IC697ACC624
IC697ACC644
IC697ACC700
IC697ACC701
IC697ACC702
IC697ACC715
IC697ACC720
IC697ACC721
IC697ACC722
IC697ACC723
IC697ACC724
IC697ACC726
IC697ACC727
IC697ACC728
IC697ACC729
IC697ACC730
IC697ACC732
IC697ACC735
IC697ACC744
IC697ACC775
IC697ACC800
IC697ACC801
IC697ACC802
IC697ACC803
IC697ACC804
IC697ACC805
IC697ACC820
IC697ACC821
IC697ACC822
IC697ADC701
IC697ADC701RR
IC697ADS701
IC697ALG230
IC697ALG230RR
IC697ALG234
IC697ALG320
IC697ALG320RR
IC697ALG324
IC697ALG440
IC697ALG440RR
IC697ALG441
IC697ALG441RR
IC697ALG444
Current Ranges
The default range is 4 to 20 mA with user data scaled so that 4 mA
corresponds to a count of 0 and 20 mA corresponds to a count of
32000. The other ranges are selected by changing the configuration
parameters using the IC641 configurator software or the Hand-Held
Programmer. The range can be configured so that the input range is
0 to 20 mA with user data scaled so that 0 mA corresponds to a
count of 0 and 20 mA corresponds to a count of 32000. Full 12-bit
resolution is available over the 4 to 20 and 0 to 20 mA ranges.
A 4 to 20 mA Enhanced range can also be selected. When this range
is selected, 0 mA corresponds to a count of –8000, 4 mA corresponds
to a count of 0 (zero) and 20 mA corresponds to a count of +32000.
The Enhanced range uses the same hardware as the 0 to 20 mA range
but automatically provides 4 to 20 mA range scaling with the
exception that negative digital values are provided to the user for
input current levels between 4 mA and 0 mA. This gives you the
capability of selecting a low alarm limit that detects when the
input current falls from 4 mA to 0 mA, which provides for open-wire
fault detection in 4 to 20 mA applications. High and Low alarm
limits are available on all ranges. Ranges can be configured on a
per channel basis. The module also reports module status and
user-side supply status to the CPU.
Power Requirements and LEDs
This module consumes 120 mA from the 5V bus on the PLC backplane
and also requires 65 mA
plus current loop current(s) from a user supplied +24V supply (see
Table 3-13, Specifications).
There are two green LED indicators on the module which provide
module and user supply
status. The top LED, MODULE OK provides module status information
on power-up as
follows:
ON: status is OK, module configured;
OFF: no backplane power or software not running (watchdog timer
timed out);
Continuous rapid flashing: configuration data not received from
CPU;
Slow flashes, then OFF: failed power-up diagnostics or encountered
code execution error.
The bottom LED, User Supply OK, indicates that the user provided
24V supply is within
specifications, thereby enabling the analog side of the module to
work properly.
Terms:
We ships worldwide and accepts T/T and Paypal.
All items are subject to availability and passing our QA testing
and
inspection.
Turnaround Time:
Standard order processing is 1-2 business days plus shipping method
chosen.
Rush and off-hours service available for an additional fee.
Packaging and Handling:
Items are safely packaged in custom shipping cartons for
protection.
Shipping:
We ship worldwide use UPS,FedEx, DHL or Truck Freight when meeded.
Call to use a shipping service other than the ones listed.
International Customers are responsible for all Customs fees, VAT
and other
fees applied by their respective countries.
All shipments are fully insured.
Our advantage Products:
【Yaskawa】Servo Drive / Servo Motor
【Mitsubishi】Servo Drive / Servo Motor
【Honeywell】Module DCS / PLC
【Emerson】DeltaV Module / Servo Motor
【ABB】Input Output Module
【AB】Module / Touch Screen
【Rosemount】Pressure and Temperature Transmitter
【Yokogawa】Pressure Transmitter
【GE】IC69 Series PLC/ Fanuc Servo Motor and Drive
(Modicon,SMC,SICK,NORGREN,Siemens etc.)
Linture Technology Co,. Ltd
Contact person: Vivian
E-mail: linture0319@163.com
Cellphone: +0086-18026552038
Wechat:18026552038
WhatsApp:+86 18026552038
Tag:electric servo drive,
ac servo drive,
ac servo pack