Home Companies Zhejiang Canaan Kaixinlong Technology Co., Ltd.

Automatic Hard Gelatin Capsule Manufacturing Machine Capsule Filler

Contact Us

[China]

Trade Verify

Address: Zone C No. 2, Wandong Intelligent Manufacturing Industrial Park, 999 Wentao Road, Ruian Economic Development Zone, Ruian City.Zhejiang.China

Contact name:

Zhejiang Canaan Kaixinlong Technology Co., Ltd.

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

Automatic Hard Gelatin Capsule Manufacturing Machine Capsule Filler

Country/Region	china
City & Province	zhejiang

Product Details

Overview of the machine:

Metal Detector And Capsule Polisher Options For Hard Capsule Filling Machine

CFK-2500 series capsule filling machine is an automatic capsule filling machine developed by our company by absorbing the advanced technology at home and abroad. The equipment is beautiful in shape, smooth operation, low noise, easy to operate and easy to clean.

The whole machine adopts intermittent rotary mechanism and quantitative filling. Suitable for 00 # -5 # capsule powder and particle filling, and can be equipped with automatic bag feeding machine, vacuum feeding machine, gold inspection machine, polishing machine, hoist and other auxiliary equipment.

Technical parameters:

Output	2500Capsules/min
No.of segment bores	18
Suitable fof capsule	00#-5#
Total power	8Kw(Standard configuration)
Overall weight	1650Kgs
Overall diemensions	1230mm×1175(+382)mm×1955mm
Noise	≤75DB(A)
Pressure	0.4 ~ 0.7Mpa
Air consumption	≤9m³
Vacuum	-0.03 ~ -0.06Mpa
Filling error	±2.5%~±5%

The machine may make technical improvements without prior notice, and the attached picture shows the options that may be offered.

Body cap separation of the empty capsule:

principle

When the empty capsule enters the module hole, the vacuum suction seat rises and is tightened with the lower module. Because the diameter of the small hole of the upper and lower module steps is less than the diameter of the capsule cap and the capsule body respectively; when the vacuum is connected, the capsule body is sucked into the lower module hole, the steps in the upper module die hole block the capsule cap down, and the empty capsule cap is separated.

Filling-type metering filling:

A-f represents the punching rod of each group, during the interval after the interval time the angle. The powder in the measuring plate mold hole is compacted by each group punching rod once. When the charging rod is lifted from the die hole, the powder box rotates, and the powder on the metering plate will automatically fill the remaining space in the die hole. Fill once, compaction once, until the sixth time, the punching rod will poke the powder column in the mold hole out of the measuring plate, so that it will fall into the empty capsule below, complete the filling work.

Use the relative movement between the scraping powder block and the measuring plate to scrape the excess powder on the surface of the measuring plate to ensure the measurement requirements of the powder column.

The characteristics of the packing-type measurement method

1. The loading amount is accurate, and the difference of the loading amount of> 0.3g is controlled within ± 3%.

2. Adjust the lifting height of the punching rod to fine-tune the dose of drug filling.

Rejection station:

Use

Some empty capsules may keep the body cap still for some reason, and remain in the upper module hole; to prevent mixing into the finished product, they are removed before the capsule is closed.

Principle

A push hand that can reciprocate up and down, located between the upper module and the lower module, with a thimble hand. When the upper and lower modules rotate, the push hand stops at the lower limit position and the thimble breaks away from the upper module. When the module stops at this station, the push hand goes up and the thimble mounted on the push hand is inserted into the upper module hole.

①. If there is a pulled out capsule cap in the upper mold hole, the upward top has no impact on the capsule cap.

②. If there is an open empty capsule in the upper mold hole, the upper module is pushed out by the upward thimble and sucked into the air chamber.

Locking station:

Use

Lock the capsule of the push rod to meet the requirements of the finished product.

Principle

The upper and lower modules are rotated to the lock, when the axis of the upper and lower modules overlap. The upper baffle above the module begins to move against the top bar below. The upper baffle presses the capsule cap, the top rod rises, and the capsule cap body is closed and locked