2 Meters Rotating Table Or Turning Table With Big Sizes For IG
Units
This rotating table is used for making double glazing glass units
with manual silicone sealants spreading machine
by sealing gun.The base rotating table does not has rollers. Other sizes of the
rotating table have rollers for supporting and rotating big size. The rotating table has different size. The base rotating table is
suit for about 1000mm*1000mm, 1500mm*1500mm, 2000mm*2000mm and
2500mm*2500mm.
Rotating Table Machine
Main feature
• Easy operating, simple and flexible
• It is used for fixing and rotating glass when manual coating the
outside of IG glass
• The middle sucker is suitable for small pieces of
glass,however,extra support frame is for large pieces of glass
1,Usage
LJZT03 Rotated sealant-spreading table is last preface of creation
insulation glass or act wall glass. It is a rotated table for draw
double group gum. It can proceed 90°Integral times rotated,also can
proceed face or contrary rotated. Revolve and vacuum sucker have
auto control equipment, it can combine glass size freedom choice
sucker and stretch arm control. Stretch arm of Special creation can
guarantee the top flat surface on a flat surface. This rotated
sealant-spreading table is rotated steady; Break down low, prop up
the stability. It is an ideal equipment to create insulating glass.
2,Main technical parameters
Working environment Parameter Unit Remarks
Working environment temperature 15-40℃
Carry/deposit temperature -20-55℃
Carry/deposit humidity 30-90%
Basic characteristic
Input voltage AC400V±10%,60HZ
Input power 120 W
Rotated speed 6.5 r/min
Air consumption 0.5-0.8 Mpa
Max glass size 2000*1500 mm
Min glass size 200*200 mm
Dimensions 600*450*950 mm
3,Main construction
This machine include Adjust flat bottom,Prop up,Revolve to prop up
the device,Spread to move the device, spirit carries control
system, electric appliances control system and plank.
3.1 Revolve prop up the device
Revolve prop up the device include the prop up,prop up the
pole,prop up set,big sucker, small sucker.
3.2 Spread to move the device
This device consisted the Spread to move the deceleration
electrical engineering,decelerate machine and chain round.
3.3 Spirit carries control system
This system included the Spirit source processor, electromagnetism
valve, singled direction valve and vacuum occurrence machine, pass
the system control the matches of the size sucker.
3.4 Electric appliances control system
This system consisted the spread to feel machine, after the
electric appliances, electric appliances a piece that break the
machine and can operate constitutes,working dependable, operation
is simple, automation the degree is high.
4,Installation and adjustment
This machine body must be grounded of dry, have no the powder and
have no the corrosion, temperature at 10-40℃. Regulate to adjust
flat bottom, make the machine keep the level, check completely
whether all tight firmwares conjunction place loosen or not move,
combining tight.
Use multi-skein-wound annealed copper in double-color of
yellow-green, with a sectional plane of 4mm2,the resistance between
the machine body and the principal grounding spots after grounding
should less than the 4Ω.
5,Use and operation
5.1 Glass size ≤500*400mm
Fix the big sucker to prop up the dish in the turn-over first last,
put on to change to deal with contact quickly, place the power
supply knob switch in the " open" position, order the feet that
move the vacuum sucker control step the switch, regulating
manometer control knob, make the vacuum degree attain the fit
pressure value( according to sucker glass prison then, do not
adjust too big), according to the operation habit, change direction
the electrical engineering to knob to place in the position
between" positive" or" anti", order first the feet that move the
vacuum sucker control step the switch( otherwise the electrical
engineering do not turn), then order to move to turn to move the
feet steps the switch, can immediately proceed the operation.
5.2 Glass size ≥550*400mm
Prop up big sucker to dish to ascend to dismantle from the
turn-over first, will change to deal with contact to change the
small sucker spirit road inside quickly, then put the glass on the
small sucker, regulate the length that prop up the pole according
to the vitreous size, then turn to use to support the pole, making
prop up the tight in a bolt for coming in contact with all glass
then, willing prop up a top finally. The rest is together 5.1
6,Attention
6.1When tune up to prop up the tight in a bolt for and glass
contact even empress, must will prop up a top, prop up otherwise
the pole turns to move, prop up, the round escapes from the glass,
will produce the glass move the phenomenon.
6.2Big sucker in usage, doing not want will enter the barometric
dint adjusts of over high, otherwise the vacuum a glass for too
bigger, being usage thickness is thinner, easy is ground the glass.
7,Maintenance
7.1 New machine through revolving of a period of time after, should
open the plank, check whether each tight firmware loosen or not
moves, laying equal stress on the new tight.
7.2 Make to complete each time, want to clean dust and gum
clearances of the machine, combine to cover the turn over dish,
keep dust from falling into sucker.
7.3 Prop up set and prop up the pole should periodically draw the
lubrication grease, resisting rust.
7.4 The periodical check electricity connects whether line loose or
not moves, and connect the dependable of the ground.
Paremeters :
| Power supply | 380V 50Hz |
| Total power | 0.37kw |
| Operating dimension | 1500*1500mm |
| Dimension | 600*550*985mm |
