Electric Servo Drive Industrial Yaskawa 100W Input 50/60HZ 0-55℃ SGDM-01ADA-R
Quick Details
Model Number: SGDM-01ADA-R
Input Voltage:200-230V
Input AMPS : 2.0
Input Frequency:50/60HZ
Input PH : 1
Series : Sigma 2 (Σ-II Series)
Output Power : 100W
Output Voltage: 0-230V
Output AMPS: 0.87
Output Frequency:0-300Hz
Temperture: 0-55℃
Place of Origin:Japan
Efficiency:IE 1
Similar Products
SGDM-01AD
SGDM-01ADA
SGDM-01ADA/SGDH-01AE+SGMAH-01AAA21
SGDM-01ADA+SGMAH-01AAAG761
SGDM-01ADA-RY5
SGDM-01BDA
SGDM-02ADA
SGDM-02ADA/SGDH-02AE+SGMAH-02AAA21
SGDM-02ADA+SGMAH-02AAA2C
SGDM-02ADA+SGMPH-02AAA41
SGDM-02ADA+SGMPH-02A1A21
SGDM-02AD-R
SGDM-02BDA
SGDM-02BDA
SGDM-02BDA+SGMAH-02BBAB1
SGDM-04AC-AD2B
SGDM-04AC-SD1
SGDM-04AC-SD2A
SGDM-04ACSD2B
SGDM-04AC-SD2B
SGDM-04AC-SD2BM
SGDM-04AC-SD2M
SGDM-04AD
SGDM-04AD+SGMAH-04AAA41
SGDM-04ADA
SGDM-04ADA +SGMAH-04AAA21
SGDM-04ADA +SGMAH-04AAA41
SGDM-04ADA+SGMPH-04A1A21
SGDM-04ADA-RY1
SGDM-04ADAY360
SGDM-04AD-R
SGDM-04AD-RY1
SGDM-04ADY39
Installation and Maintenance: Installation and maintenance or
replacement must be carried out by suitably qualified service
personnel, paying particular attention to possible electrical and
mechanical hazards. Weight: Large drives are heavy, the center of
gravity may be offset and removable covers shield internal
components. When handling, take appropriate precautions and lift
the equipment using permanent, fixed surfaces, such as the base;
avoid lifting the device using protective cover shields that may be
loose. Beware of sharp edges; use protective gloves when handling
such assemblies. Flying Leads and Loose Cables: Ensure that flying
leads or loose cables are suitably restrained, to prevent snagging
or entanglement, or are disconnected before carrying drives with
such leads or cables. Generation: If a motor is driven
mechanically, it may generate hazardous voltages which are
conducted from its power input terminals to the drive.
The power connector must be suitably guarded to prevent a possible
shock hazard. Loose Drives: When running an unmounted drive, ensure
that the cooling fan is adequately guarded and sufficient airflow
is provided around the drive to ensure adequate cooling. The
mounting surface of the drive is a heat sink and its surface
temperature may increase when the drive is operating. If a motor is
connected to the drive, remove the key which otherwise could fly
out and restrain the motor before applying power to the drive. Da
maged Cables: Damage to cables or connectors may cause an
electrical hazard. Ensure there is no damage before energizing the
system. Supply: Drives connect to a permanent main power source;
not a portable power source. Suitable fusing and circuit protection
devices are required. Consult the instructions and adhere to local
and national regulations before connecting and energizing the
drive. Safety Logic Signals:
Logic signals from the drive are interruptible signals; they are
removed when power is removed from the drive. Consult the manual
for information on auxiliary power connections that may be employed
when these signals are used for safety purposes. Safety
Requirements: The safe incorporation of Tol-O-Matic SSD products
into a machine system is the responsibility of the machine
designer, who should comply with the local safety requirements at
the place where the machine is to be used. In Europe this is likely
to be the Machinery Directive, the ElectroMagnetic Compatibility
Directive and the Low Voltage Directive.
In the United States this is likely to be the National Electrical
Code. Mechanical Connection: Drives must be installed inside an
electrical cabinet that provides environmental controls and
protection. Installation information for the drive is provided in
the manual and list the minimum installation requirements for the
drive are provided in the manual. Motors and controlling devices
that connect to the drive should have specifications that
complement the capabilities of the drive. Motors: Motors controlled
by the drive should only connect to the drive; they should not
connect directly to the AC line. U
The added or improved functions differ depending on the SERVOPACK
model or software version number:
• SGDM-D
• SGDM-DA
• SGDM-A
(Software version No. 32 or later) Refer to the following table for
the added or improved functions for each model. This table can also
be used in reference to other SERVOPACK models.
Function Item Description Σ-II Series SERVOPACK SGDMReference D
DA Section DA with Software Version No. 32 or later
Applicable capacity range 30W to 3.0 KW Applicable Applicable
Applicable - 30W to 15.0 kW N/A Applicable Applicable - Speed feed
forward In the position control mode, the speed feed forward
reference using an analog voltage can be input by the speed
reference (VREF) input. N/A Applicable Applicable 9.4.3 Torque
limit using an external torque limit and analog voltage reference
To enable the torque limit function using analog voltage reference
only when either /P-CL or / N-CL signal is ON. N/A Applicable
Applicable 8.9.4 Input signal polarity reversal To reverse the
“Enabled” logic polarity of sequence input signal N/A Applicable
Applicable 7.3.2 Output signal polarity reversal To reverse the
“Enabled” logic polarity of sequence output signal N/A Applicable
Applicable 7.3.3 Multiturn limit setting To set the upper limit of
multiturn data when using an absolute encoder. N/A Applicable
Applicable 8.4.7 “Multiturn limit disagreement” alarm detection To
detect the alarm A.CC when the multiturn limit value set in the
encoder does not agree with that in the SERVOPACK. N/A Applicable
Applicable 8.4.8 Average movement filter of position reference To
filter the position reference pulse of constant frequency inside
the SERVOPACK. Either acceleration/deceleration filter or average
movement filter can be selected. N/A Applicable Applicable 8.6.4
Notch filter Filtering function to suppress vibration according to
the machine’s vibration frequency. N/A Applicable Applicable 9.4.10
Second stage notch filter and changeable Q value A second stage
notch filter is added. And the Q value (sharpness of notching) can
be changed. N/A N/A Applicable 10.3.4
OTHER SUPERIOR PRODUCTS
Yasakawa Motor, Driver SG- Mitsubishi Motor HC-,HA-
Westinghouse Modules 1C-,5X- Emerson VE-,KJ-
Honeywell TC-,TK- Fanuc motor A0-
Rosemount transmitter 3051- Yokogawa transmitter EJA-
Contact person: Anna
E-mail: wisdomlongkeji@163.com
Cellphone: +0086-13534205279
