Guangzhou Debo Machinery Mfg Co.,Limited |
|
A3 / A4 book binding machine, perfect book binding machine
High quality binding machine for book
Glue binding machine using common problems and solutions
One, out of the book binding, spine cover wrinkled how to do?
Solution: 1. Adjust the thickness of the cover, under normal
circumstances, more than two hundred books is best to use the cover
of more than 230g paper. 2 adjust the level of the platform facing
surfaces, the home side platform appropriate to reduce, can be
resolved. Similarly, if the spine is not binding books out side the
home side the platform to increase the number can be solved.
Second, do not glue
Solution: a view plastic box of plastic is not too small, more than
the minimum. 2 adjustment lever scraping gum, the gum scraping
lowering the bar, increase the amount of glue, but not too large,
when the glue is too large, there will be a large side glue, led
directly to the side of the plastic overflow, affecting the
appearance of books.
Third, the tire does not turn
Solution: a view plastic box does not turn the motor is not, to be
replaced if the motor does not turn the motor. 2 viscose cause the
chain to see whether the chain will not bend, such a case, replace
the chain. 3 tire sleeve must be regularly refuel, make plastic
axle adequately lubricated. 4 Replace the plastic when using glue
to a certain extent, will be black rubber thickens, it needs to be
replaced, be sure to pay attention to; try to use glue melting
point of not more than 145 degrees.
Fourth, the car does not go
Solution: First, there are two check around limit sensors,
detection methods, one to let the car go from left to right, in the
car to the right half of the time limit sensor depressed, to see
whether the car will stop, if it shows right would limit sensor no
problem, let the car returned, pressing the left limit of the
sensor in the return, the above, as the same thing, it shows the
sensor no problem. 2 In the case of shutdown, according to the E
key, boot into the first item, and then press the "cutter" button
and let the car right away, when the car went head to see if there
is a number from 0 on the display, if then press "paste head" key
to return, when the car went to the left, the display shows the
number 1, so that the sensor is no problem, or we need to replace
the sensor.
Five, the car does not clamp
Solution: a first look at the lower part of the car if there is
glue. If glue need to scrape gum, under normal circumstances can be
solved. If not enough you need to check the car to open the trip
switch and infrared sensors, if there are questions, you need to
replace the sensor, if not on the need to replace the motor or the
motherboard.
Six, clip surface station does not clip
Solution: First, enter the self-test program, the next turn to face
the sensor detects clip, press the "paste head" key to see whether
the clamping clip surface units, if the clamp on the press "Cutter"
button to see if open, if you open the binding of the can. 2 If the
above procedure does not work, then you need to check the motor and
gear clamp surface units, if there are problems need to be
replaced, otherwise the motherboard problem.
Seven, do not turn cutter
Solution: Check the fuse is burned out, the fuse next to the
machine on the left side of the power cord has a black knob, open
new ones insurance can, in general, the cutter motor is not bad, if
does not work, then, is the problem the motherboard or SCR.
Eight, plastic boxes without heating or the temperature is too high
Solution: First check whether heating pipes or heating plate is
heated, not heated thread must first check whether there are
oxidized and, if please clean up. Check the temperature is too high
a temperature controller, see the thread is loose, as loose the
thread re-insert it, otherwise they need for a temperature
controller.
Nine, slotting cutter too deep or too shallow
The solution: push the car to the right, then the next lock is
loose on the set of the platform below the four screws, such as
deep aboard a low profile milling, contrary to the high profile.
(Must bring four corners transferred to a parallel line, otherwise
there will be a deep one shallow)
Specifications
Item | 420mm wireless glue binding machine |
Model no | DB-60U |
Max. Binding Length | 420mm (A3 size) |
Max. Binding Thickness | up to 6.0cm |
Max. binding speed | 450 books/hour |
Book cover thickness | 70P-250P |
Rail | Dual |
Working mode | One time from left to right |
Display | Touch LCD, code display+touch operation |
Manual/Auto conversion | Yes |
Clamping mode | Automatic detecting by magic eye |
Milling | Small milling cutter+sun milling cutter |
Glue melting time | 20 Mins |
Power | AC220V (220V) 50HZ (60HZ) 1.2kw |
Machine size | 1450mm×620mm×1100mm |
Machine weight | 250kgs |
DB-60U A3 Wireless glue binding machine, perfect book binding
machine
DB-60U hardcover book binding machine
High quality binding machine for book
Note the use of glue binding machine:
1, to avoid the simultaneous operation of two machines;
2, please do not replace the cutter itself, to prevent the
phenomenon of paper off the glue binding process.
3, cutter for when the action starts, but as usual wishing cutter
cover is open, press the emergency stop button when;
4, plastic tank heated to high temperatures, the temperature of
about 170-190 ℃, can not touch;
5, maintenance in order to avoid electric shock, unplug the plug;
6, when the hot melt adhesive reaches the bottom of the black line
indicates the board, shall be added;
7, when added directly into the plastic glue tank, glue not exceed
the top of the black line, so as not to overflow plastic tank
outside cause parts damage.