Steel Plate Welded Frame Cu Wire Drawing Machine With Electrical Control System

HXE-20DT Fine copper wire drawing machine with annealer
 
I. Quick description
 
    HXE-20DT Fine copper wire drawing machine with annealer is used to draw and anneal single bare copper wire from 0.8mm-1.6mm to 0.15mm-0.55mm.
 
II. Components
 

 
III. Main Technical parameters
 
1. Usage single bare copper wire drawing and annealing
2. Inlet size 0.8mm-1.6mm
3. Outlet size 0.15mm-0.55mm (Elongation of annealed wire 25% to 32%)
4. Machine speed/max 1800m/min
5. Die number 20, Dies size 25mm×8-10mmT, Slip ratio 15%+8%
6. Wire drawing mode standing-mode and 4axes
7. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine
8. Main motor 15KW, Spooler motor 3.7KW, China best brand
9. Annealing voltage DC50V/max, Annealing current DC450A/max, Annealing power 22KVA
10. Annealing method DC Three section annealing
11. Annealing protection will be done by steam protection
12. Capacity of compressed air 0.4-0.6Mpa, 20L/min
13. Demand Water quantity for annealing and coolant 200L/min
14. Machine frame welded by steel plate
15. Transmission Flat belts
16. Capstan Ceramic plasma
17. Lubricating system Pipe Spray
18. Bobbin size 300mm, loading capacity: 50kg/max
19. Bobbin loading & unloading type shaft type
20. Traversing unit 110W synchros motor, width: 270mm/max
21. Tension control by Air pressure tension control (With Weight balance as Backup)
22. Cabinet 0.8m*0.6m*2.0m
23. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m
24. Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.
 
IV. Operating procedures
 
4-1. Open power switch
4-2. According to the wire diameter, choose the dies (Check the die list).
4-3. Use pliers to break the wire to get a smaller section.
4-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).
4-5. Wire direction, please check the Drawing for Wire path.
4-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.
4-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.
4-8. Set the length meters, then press the Start button to start the machine.
 
V. Attention
 
5-1. If wire breaks, will stop automatically, and the Fault Indicator light will open.
After connect the wire, press the Fault Reset button(Yellow button) and the On button (Green button), to run the machine again.
5-2. Press Emergency Stop button(Red button) to shut down the machine immediately.
After solve, press the button again to run the machine.
5-3. After set the Length-counter, the machine will stop automatically when reach the length set.
After change the Spool, please press the Length Reset button(Yellow button) and the Spool Reset button(Yellow button) to run the machine again.
5-4. After the machine stop(no running at all), then switch the Pump switch to stop the lubrication.
5-5. Do not touch the wire in the Annealing section.
5-6. After shut down the machine, need at least 30 seconds to restart the machine.
5-7. Wire often breaks, adjust the speed, balance arm, check the dies are clean or not.
5-8. If has scratch on the surface of the wire, check the capstans on the Take-up part. Check the drawing capstans.
 
VI. Advantage and after-sale service
 
A: Advantage
 
(1). HENGXIE has some world famous parts suppliers, has special lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our own factory , quality is reliable.
(3). DC. three-section annealing
(4). Our company’s developing process in more than 10 years.
 
B: After-self service
 
Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
 
      Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.
A. Due to wrong operation while shipping.
B. Due to Buyer`s wrong preparation that may cause damage to the machine.
C. Due to Buyer`s wrong operation that may cause damage to the machine.
D. Not in the consuming part list.
E. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.
F. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.
G. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.