22 DT Fine Copper Wire Drawing Machine With Annealer & Large Spool , Small Wire Drawing Machine

HXE-22DT Fine copper wire drawing machine with Annealer & large spool

I. Application

       HXE-22DT Fine copper wire drawing machine with annealer is used to draw and anneal single bare copper wire from 0.8mm-1.8mm to 0.3mm-1.0mm.

II. Components

III. Main Technical parameters

1. Usage single bare copper wire drawing and annealing

2. Inlet size 0.8mm-1.8mm

3. Outlet size 0.3mm-1.0mm (Elongation of annealed wire 25% to 32%)

4. Machine speed/max 1500m/min

5. Die number 22, Dies size 25mm×8-10mmT, Slip ratio 15%+8%

6. Wire drawing mode standing-mode and 4axes

7. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine

8. Main motor 22KW, Spooler motor 15KW, China best brand

9. Annealing voltage DC60V/max, Annealing current DC1000A/max, Annealing power 60KVA

10. Annealing method DC Three section annealing

11. Annealing protection will be done by steam protection

12. Capacity of compressed air 0.4-0.6Mpa, 20L/min

13. Demand Water quantity for annealing and coolant 200L/min

14. Machine frame welded by steel plate

15. Transmission Flat belts

16. Capstan Ceramic plasma

17. Lubricating system Pipe Spray

18. Bobbin size 300mm, loading capacity: 50kg/max

19. Bobbin loading & unloading type shaft type

20. Traversing unit 110W synchros motor, width: 270mm/max

21. Tension control by Air pressure tension control (With Weight balance as Backup)

22. Cabinet 0.8m*0.6m*2.0m

23. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m

24. Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.

IV. Machine structure

       Annealing method is DC Three section annealing, there are three contact capstans, as Pre-Heating, Annealing and Drying. For drawing machine part, there is belts that connection from the Fix-speed capstan to the Annealer machine to achieve the transmission, as keep same speed.

Connect the Up capstan and Down capstan with Positive and Negative power, to make the wire in a short circuit, to achieve the heating.

There is annealing plate to auto track and adjust the speed and annealing voltage.

To achieve fast coolant to make the wire soft(Annealing), the Down capstan is immersed into the coolant water(There is a water tank in the bottom of the Annealer machine), coolant water is 0.5% emulsion. With the Pump to pump the coolant water through all pipes and valves, half sealed annealing door. Adjust the valves to adjust the coolant water in certain height.

To make sure the wire no oxidation, in the annealing protection pipe has steam (Buyer self will prepare Steam generator).

In the drying section, has a blowing device (Require two Tungsten dies, Buyer self prepare), by compressed air (Buyer self prepare Air compressor) to blow the water on the surface of the wire.

Lubrication oil concentration of mix with water 2-3%.

V. Advantage and after-sale service

A: Advantage

(1). HENGXIE has some world famous parts suppliers, has special lubrication system for the gears and bearing.

(2). Body and other key components and parts are produced by our own factory , quality is reliable.

(3). Our company’s developing process in more than 10 years.

(4). DC. three-section annealing

B: After-self service

Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:

(1) 1 year for mechanical part.

(2) 6 month for electrical part.

      Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.

A. Due to wrong operation while shipping.

B. Due to Buyer`s wrong preparation that may cause damage to the machine.

C. Due to Buyer`s wrong operation that may cause damage to the machine.

D. Not in the consuming part list.

E. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.

F. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.

G. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.