15KW 26DW Fine Copper Wire Drawing Machine Durable 2235mm*1575mm*1590mm

HXE-26DW Fine copper wire drawing machine

I. Quick description

     HXE-26DW Fine copper wire drawing machine is used to draw single bare copper wire from

0.8-1.65mm to 0.12-0.35mm.

II. Specifications

1. Inlet wire diameter:0.8-1.65mm
2. Outlet wire diameter:0.12-0.35mm
3. Speed:2000mpm
4. Dies number:26
5. Slip ratio (Area reduction) : No.1 -No.25 / 13%; No.26 / 8%
Elongation, no annealing, 1%-2%, After annealing, 17%-25%. Tensile strength 200-300 MPa
6. Wire drawing mode:horizontal-mode and 4 axes
7. Driver: by dual Inverters control, Brand: Inovance,Chinese famous brand, 15kw+3.7kw.
8. Main motor: 15KW AC 3 phase motor
9. Spooler motor:3.7KW AC 3 phase motor
10. Motor brand: Wan Nan motor, China classical brand
11. Capstan:steel with ceramic coating,
12. Max capstan diameter:242mm
13. Max fix speed capstan:207mm
14. Machine structure:cast iron
15. Reverse system: PID synchronous control spool
16. Transmission: by Flat belts+timing belt
17. Pay-off method: over-head
18. Tension control:weight balance by swing arm
19. Lubrication type: spray, Grade 2.5%-3%, Capacity 40L/min,
Lubrication tank: L1000mm*W500mm*H600mm
20. Bobbin size: 300mm, material steel, 17kg.
21. Take up: shaft type
22. Bobbin capacity:50-60kg/max
23. Brake: Pneumatic brake
24. Power source: customize
25. Machine dimension: L2235mm*W1575mm*H1590mm, Machine weight: 2000KG

III. Components

 
IV. Preparation

(1) Check if the oil is correct, if the oil inside the oil drum accord request, if each part of the machine is clean, pay special attention to the place around the switch, make sure no oil or dirt.

(2) Confirm the three phase power supply, voltage 380V, 50HZ.

(3) If the power cable has cut.

(4) if the ground wire is connected correctly

(5) If the oil type for wire drawing is correct, any change of the oil character, any dirt in the oil.

(6) If the wire size in the range, if the material is the correct model.

(7) Check the correct specification of the iron shaft, no sharp end, pay special attention to see any damage on the contact surface between inner hole of the iron shaft and the lock blot, balance correction should less than G6.3.

(8) If the bobbin is tightened by wrench.

(9) If the trolley is kept away from the bobbin.

(10) If the copper wire feeding device is working smoothly.

(11) If the machine surrounding area is clean

(12) If any leakage of oil or water from the machine.

(13) Check if the dies arrangement and distribute correct, and if the dies direction is correct. (calculate with section reduce rate)

(14) If the a guide pulley is adjusted within the width of the wind shaft.

(15) If the fan inside the electric control box is working normally

(16) If the base ground is strong enough.

(17) If any dirt in the spraying system.

 
V. Advantage and after-sale service
 
A: Advantage
 
(1). HENGXIE has some world famous parts suppliers,has special lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our own factory , quality is reliable.
(3). Our company’s developing process in more than 10 years.
 
B: After-sale service
 
Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.