I.The technological conditions1.Pulp density:0.2-0.3%2.Before in to drying cylinder dryness ratio:36-40%3.Wrinkling dryness ratio:92-93%4.Wrinkling ratio:20-25%5. Finished paper have water ratio:7-8%II.Blanket tensionBlanket tension:Design tension 4KN/m.III.Require for water.electricity.steam.compressed air1.Clear waterPressure:1.6 MPa(high pressure water must be approved by 100 mesh screen strainer)2.ElectricityMotor voltage:380V AC /50hz three phase220V AC /50hz single phaseControl voltage:220V AC /50hz single phase24VDC3.Steam pressureDrying cylinder MAX use steam pressure:0.5 Mpa(working pressure)4.Compressed airRequire:filtering.oil removal.water removal.desiccativeCompressed air source pressure:0.7MPaUse pressure:≤0.6MPaStructure And ConfigurationI.OverviewThis machine apply to production toilet paper , napkin paper , face
tissue paper , handkerchief paper , making quantitative 12-30g/m2 , can use paper pulp : Waste paper pulp ; Wood pulp ; Straw pulp ;
Bamboo pulp .Main component : Forming part ; Dry part ; Roll paper part ; Drive
part .II.Forming PartMain component : cylinder vat ; wove mould ; arched plate ; couch
roll ; suction water tank ; blanket washing device1.Cylinder vatQuantity : 1Grouting system whole use Q235 steel plate manufacturing , small
arched plate use corrosion resistant plate manufacturing and also is adjusting
device ,cylinder vat is enclosed type .2.Wove mouldQuantity : 1Specification:φ1800×3200×3800mmType:stainless steel winding sheet type ,stainless steel rodφ12mm and 304 winding sheet 12×1.5mm,spacing≤9mm,spokes foundry
iron manufacturing ,spacing 175mm.Wove mould level surface,variance < 0.15mm/m .check static balance,does not allow any weight deviation
.3.Couch rollQuantity : 1Specification:φ650×3200×3800mmMaterial:roller body use seamless steel tube manufacturing ,both axle head
use 45# steel manufacturing , elimination of stress .coating soft
rubber in the surfaces , thickness 30mm.rubber hardness SHAW "A"35±20 , check dynamic balance .4.Suction water tankQuantity : 2Length:3200mm,sucker mouth length :2900mm;specifications 5 aperture.Tank body use corrosion resistant plate welding manufacturing , face-plate material is high polymer polyethylene plate , thickness
30mm .5.Spray water pipeA. Needle type spray water pipe,pore size 0.8mm,stainless steel
pipe body and nozzle,ceramic core.Quantity : 2Move mode:motor-driven back and forth.B.Fan-shaped spray water pipeQuantity : 1Stainless steel pipe body and fan-shaped nozzleMove mode:fixed.6.Guide rollerQuantity : 8Specification:φ240 ×3300 ×3800mmUse φ245×14 seamless steel tube manufacturing,foundry iron choke plug ,axle head use 45# steel manufacturing ,thermal refining
,surface chromate treatment 0.1mm;check dynamic balance.7.Unfold blankets rollerQuantity : 1Specification:φ265×3300×3800mmUse φ245×14 seamless steel tube manufacturing,foundry iron choke plug ,axle head use 45# steel manufacturing ,thermal refining
,coating rubber in the surfaces , thickness 30mm.rubber hardness
SHAW"A"97±2 , check dynamic balance .8.Corrector unitQuantity : 1Type:Double pneumatic drive,pneumatic auto correcting ,and also can
manual operation ;equip with signal generator.9.TensionerQuantity : 1Dual purpose for manual operation and auto ,stainless steel
pipe.threaded rod ,copper screw nut .II.Dry PartMain component : drying cylinder.carrying roller.steam
cover.scraper.machine frame .1.Drying cylinderQuantity : 1Specification:φ3000×3200×3800mm,check static balance.Material:cylinder use HT300 foundry iron manufacturing ,add nickel alloys.chromium.copper .percentages: nickel alloys:0.4%,chromium:0.6%,copper:0.6% , drying cylinder cover use HT250 foundry iron manufacturing.Cylinder surface hardness:≥HB 210Processing precision:surface roughness Ra=0.3-0.4μmMAX use steam pressure:0.5 Mpa(working pressure)Water test pressure:1MPa.Equip with rotary steam coupling and fixed siphon tube .Gear box : use foundry iron manufacturing .Small gear: use cast steel manufacturing .2.Groove carrying rollerQuantity : 1Specification:φ650×3200 ×3800mmMaterial:roller use foundry iron manufacturing,both axle head use 45# steel
manufacturing , elimination of stress .coating rubber in the
surfaces , thickness 25mm.rubber hardness "A"95±20 , check dynamic balance .Center height 0.70-0.75mm , design line pressure 80KN/m3.Hold water receptacleQuantity : 1Welding manufacturing4.Steam coverQuantity : 1Use enclosed type steam cover , antirust aluminium manufacturing ,
framework use section steel tomanufacturing .5.Pneumatic scraper and pedestalQuantity : 1Compound pressure type structure,alloy-steel blade.6.Machine frameUse δ=12~30 steel plate after bending welding manufacturing,box type
structure,vibration stress relief process,equal height
deviation≤0.05mm.7.Walking board.Walking board support.Ladders.BanisterIn the drying cylinder operation side , between the drying cylinder
and roll paper cylinder have Walking board and banister , use
section bar welding manufacturing , walking board laying insert
tread .III.Roll paper partRoll paper cylinder : φ800×3000×3800mmUse steel plate δ=20 coiled manufacturing .after the welding process,make sure MAX roll paper
diameter reach φ900mm stiffness is no problem ;check static balance.Pressure paper roller φ300×3000mm,coating rubber thickness
20mm,rubber hardness "A" 70±2°.Roll paper shaft quantity : 4 .use seamless steel tube to
manufacturing .IV.Drive partUse Variable Voltage Variable Frequency ; Separate drive , have
three drive point , use hardened reducer .Wove mould | 11K W |
Drying cylinder | 90 KW |
Roll paper machine | 7.5 KW |
Auxiliary drive point :Wove mould suction fan | 2.2 KW |
Tensioner electric motor | 1.1 KW |
Steam cover draft blower | 7.5 KW |
V.Air control box
Control part:couch roll air cylinder.corrector unit pneumatic tires.carrying roller
pneumatic tires.wrinklingscraper.break of paper scraper.
VI.Lubricating
Except bearing reducer , whole use grease to lubricating
VII.Foundation part
Foundation plate.foundation bolt.
Foundation plate use foundry iron HT200 to manufacturing , after
aging treatment processing .
Control System
I.Air controlled system
This system include control to operation box and whole air point
pipeline . execute component etc .
II.Electronic control system
Use Variable Voltage Variable Frequency control system . frequency
converter use "ABB"
Whole electronic control system use PLC digital communication
system program control . operation easy , stable performance , run
credibly , excellent static and dynamic performance , quick
response .
Machine working speed stability , speed accuracy deviation under 0.1% .synchronization running speed meet the
overall requirements .
1.Main drive
Wove mould .Drying cylinder.Roll paper cylinder
2.Auxiliary drive
Auxiliary drive include : Electric tensioner × 1.Wove mould suction
fan × 1.Steam cover draft blower × 1 .
3.Frequency transforming cabinet use forced ventilate heat exchange
Supply Boundaries
Supply boundaries is machine first flange(or threaded pipe ) interface with the outside world .
__________________________________________________________________________
Factory Information:
1. The factory has passed PAC-SL
2. Products has passed ISO9001 quality certification
3. Many years experience of equipment manufacture
Our Services:
1. Reasonable suggestions for selection of equipment.
2. Provide detailed description and assembly drawing , to make you
more aware of the device's ability to work.
3. Engineers on-site equipment installation and commissioning.
4. Provide training for your employees.
5. Rofessional technical guidance and technical support during your
production, make sure the device's work properly and production.
6. Equipment upgrade & remould.
7. We will testing installation machine in the factory workshop ,
to ensure safety and quality.
If you have more question, Pls contact with me:
Contact: Vicky Wang
Email: sales@hengbon.com
Skype:Vicky_hengbon
Whatsapp:008615610503516
Website:http://www.hengbonmachinery.com