Active Member
|
[China]
Address: Room 702-3,Ningbo Lishi Commercial building,Lane 578,45# Tiantong South Road,Yinzhou District,Ningbo,China
Contact name:Tina Kui
VAINO INTERNATIONAL LIMITED |
|
|
servo system plastic injection molding machine for making rubbish bin turn-over box
QUIET & LOW NOISE
The machine runs with low noise ,and will be much quieter in a low speed
RELIABLE HOLDING PRESSURE
Comparing with all electric injection molding machine ,the time for pressure holding will be much longer and steady
OIL TEMPERATURE RISE SLOWLY
Servo motor proportionally deliver hydraulic oil base on our needs,it’s can prevent unnecessary heat being generated even in some cases does not require ,cooling .
EXCELLENT CHARACTERISTICS INHERITANCE
Outstanding machine stability ,being safety and dependability ,strong mechanical parts ,complete functional human-oriented operation system and long service life .
SPECIFICATION
| SPECIFICATION | M-1800 | ||||
| ITEM | A | B | C | D | |
| INJECTION UNIT | |||||
| SCREW DIAMETER | mm | 130 | 140 | 150 | 160 |
| SCREW L/D RATIO | L/D | 24 | 22 | 20 | 19.2 |
| SHOT VOLUME(THEORETICAL) | ㎤ | 10619 | 12315 | 14137 | 16085 |
| INJECTION WEIGHT(PS) | g | 9769 | 11330 | 13006 | 14798 |
| INJECTION PRESSURE | Mpa | 183 | 158 | 137 | 121 |
| INJECTION RATE | g/sec | 958 | 1111 | 1276 | 1452 |
| SCREW SPEED | rpm | 95 | |||
| CLAMPING UNIT | |||||
| CLAMP TONNAGE | KN | 18000 | |||
| TOGGLE STROKE | mm | 1600 | |||
| MIN.MOLD HEIGHT | mm | 700 | |||
| MAX.MOLD HEIGHT | mm | 1600 | |||
| SPACE BETWEEN TIE BARS | mm | 1570X1470 | |||
| EJECTOR TONNAGE | KN | 320 | |||
| EJECTOR STROKE | mm | 420 | |||
| EJECTOR NUMBER | PC | 33 | |||
| OTHERS | |||||
| MAX.PUMP PRESSURE | Mpa | 16 | |||
| HEATER POWER | KW | 93 | |||
| PUMP MOTOR POWER | KW | 45+45+45 | |||
| OIL TANK CUBAGE | L | 2800 | |||
| MACHINE DIMENSION(LxWxH) | M | 16.7X3.1X5.14 | |||
| MACHINE WEIGHT | T | 110 | |||
COMPONENT
| COMPONENT | BRAND&ORIGINAL | ||
| hydraulic system | Servo | ||
| hydraulic motor | INTERMOT-ITALY-CHINA | ● | |
| servo motor control system | HUICHUAN/PHASE-CHINA | ● | |
| hydraulic pump | fixed Pump | VICKERS OR YUKEN | / |
| gear pump | SUMITOMO-JAPAN | ● | |
| hydraulic direction valve | NORTHMAN-TAIWAN | ● | |
propotional flow control valve&propotiona l pressure control valve | HNC-TAIWAN FOR BIG MACHINE, SMALL MACHINE USE DONGFENG-CHINA | / | |
| mould adjust hydraulic motor | INTERMOT-CHINA | ● | |
| hydraulic safety valve | NORTHMAN-TAIWAN | ● | |
| electric system | |||
| computer/controller | TECHMATION-TAIWAN | ● | |
| relay | SCHNEIDER-GERMANY | ● | |
| main switch | LS-KOREA | ● | |
| linear transducer | GEFRAN-ITALY | ● | |
| limited switch | PANASONIC-JAPAN | ● | |
| breaker | CHENTAI-CHINA | ● | |
| electric motor | ZHONGDA-CHINA | / | |
| others | |||
| High pressure hydraulic pipe | GOODYEAR-USA | ● | |
| seals | VALQUA-JAPAN | ● | |
| pressure meter | Tecsis-USA | ● | |
| automatic lubrication | SL-CHINA | ● | |
| screw | JINGXING-CHINA 38CrMoAlA | ● | |
Selling points
1. More fast cycle:valve panel design in bigger hole with bigger oil pipe.Oil go though the valve more fast flow and the Machine action more goes more faster in mould open and ejector process.
2. Material charging more faster:Adopt proportional control for backpressure,can be set in the controller ,more smart and easy operation.when material charging,you can set 0 in the backpressure,so the charging will be more efficient and faster.make sure every shot to be more accurate than manual control type.
3. Adopt Techmation newest verison controller which is more fast response ,more output and input can be use for connection the robot in future.
4. Hydraulic safty protection installed in both front and rear operation door.when any door is open,the hydraulic system will be shut down to provide more safty protect for the operators.
5. Adopt 38CrmoAla Material for key in toogle part.more endurable in using.other supplier may use 40CR or 45# Steel
6. Double oil tank design:because short the distance for the oil return line ,the hydraulic system response is getting more quicker. In the meantime,this design will reduce the oil temperaure ,protect the oil seal.
7. Using bridge design for the injection unit,avoid material leakage if the injection unit is not stay in the same level.
8. Adopt double injection cylinder ,more faster and powerful.avoid any injection less or injection not in the center by single injection cylinder
9. Screw barrel material using top 3 supplier in China
Platen size:
