Home Companies Shenzhen Handar Optical Technology Co.,Ltd

Copper 10Gbps 10G SFP Transceiver HD-10GLC-T RJ45 Port SFP Max 20M

Active Member

Contact Us

[China]

Address: Add: F4, Bld.4, Xifa B industry Zone, Yintian, Xixiang, Bao'an, Shenzhen, China.

Contact name:Frank

Shenzhen Handar Optical Technology Co.,Ltd

Copper 10Gbps 10G SFP Transceiver HD-10GLC-T RJ45 Port SFP Max 20M

Country/Region china
City & Province shenzhen guangdong

Product Details

Copper 10Gbps SFP Transceiver HD-10GLC-T RJ45 Port SFP Max 20M

 

Product Features

  • Up to 10Gbps bi-directional data links
  • RJ45 Max 20m
  • Fully metallic enclosure for low EMI
  • Compact RJ-45 Connector assembly
  • Hot-pluggable SFP footprint
  • Low power dissipation
  • Extended case temperature: 0℃ to 70℃
  • RoHS compliant and Lead Free

Applications

  • 10 Gigabit Ethernet

1. Product Description

The HD-10GLC-T is Copper Small Form pluggable (SFP) transceiver, which are based on SFP multi-sourcing agreement (MSA). They are compatible with the 10GBASE-T and 1000BASE-T standards as specified in IEEE Std 802.3.The 1000BASE-T physical layer IC(PHY) can be accessed via I2C,allowing access to LIMITED PHY settings and features

 

2. Regulatory Compliance

Handar transceivers are Class 1 Laser Products comply with FDA regulations. Meet Class 1 eye safety requirements of EN 60825 and the electrical safety requirements of EN 60950.

 

3. +3.3V Volt Electrical Power Interface

The HD-10GLC-T has an input voltage range of 3.3V +/-5%,The 4 V maximun voltage is not allowed for continuous operation.

 

ParameterSymbolMin.TypMaxUnitsNotes/Conditions
Supply CurrentIs  600mA1.2W max power over full range of voltage and temperature. see caution note below
Power Supply VoltageVcc3.133.33.47vReferenced to GND
Maximum VoltageVmax  4v 
Surge CurrentIsurge  550mAHot plug above steady state current, See caution note below

Caution: Power consumption and surge current are higher than the specified values in the SFP MSA

Table 1.+3.3 Volt electrical power interface

 

4. Low-Speed Signals

ParameterSymbolMin.MaxUnitsNotes/Conditions
SFP Output LOWVOL00.5V4.7k to 10k pull-up to host Vcc, measured at host side of connector
SFP Output HIGHVOHHost Vcc-0.5Host Vcc+0.3V4.7k to 10k pull-up to host Vcc, measured at host side of connector
SFP Input LOWVIL00.8V4.7k to 10k pull-up to Vcc, measured at SFP side of connector
SFP Input HIGHVIH2Vcc+0.3V4.7k to 10k pull-up to Vcc, measured at SFP side of connector

Table 2. Low-speed signals, electronic characteristics

 

5. High-Speed Electrical Interface

ALL high-speed signals are AC-coupled internally

(1)High-speed Electrical Interface Transmission Line-SFP

ParameterSymbolMin.TypMaxUnitsNotes/Conditions
Line FrequencyfL101251000MHZ5-level encoding, per IEEE 802.3
Tx Output ImpedanceZout,TX 100 OhmDifferential, for all frequencies between 1MHz and 125MHz
Rx Input ImpedanceZin,RX 100 OhmDifferential, for all frequencies between 1MHz and 125MHz

Table 3. High-speed electrical interface, transmission line-SFP

 

(2)High-speed Electrical Interface, Host-SFP

ParameterSymbolMin.TypMaxUnitsNotes/Conditions
Single ended data input swingVinsing180 700mVSingle ended
Single ended data output swingVoutsing350 800mVSingle ended
Rise/Fall TimeTr,Tf 175 psec20%-80%

Tx Input Impedance

 

Zin 50 OhmSingle ended
Rx Output ImpedanceZout 50 OhmSingle ended

Table 4. High-speed electrical interface, host-SFP

6. General Specifications

ParameterSymbolMin.TypMaxUnitsNotes/Conditions
Data RateBR10 10000Mb/secIEEE 802.3 compatible. See Notes 2 through 4 below
Tx Output ImpedanceL  100MCategory 5 UTP.BER<10-12

Table 5. General specifications

Note:

1.Clock tolerance is +/- 50 ppm

2.By default, the HD-10GLC-T is a full duplex device in preferred master mode

3.Automatic crossover detection is enabled. External crossover cable is not required

4.Multi-BASE-T operation requires the host system to have an SGMII interface with no clocks, and the module PHY to be configured per Applications Note AN-2036.With a SERDES that does not support SGMII, the module will operate at 1000BASE-T only.

7. Environmental Specifications

The HD-GLC-T1/2 has an extended range from 0℃ to +85℃ case temperature as specified in Table.

ParameterSymbolMin.TypMaxUnitsNotes/Conditions
Operating TemperatureTop0 70 Case temperature
Storage TemperatureTsto0 70 Ambient temperature

Table 6. Environmental specifications

Hot Products

HD-1 Fiber Port &4 X 10/100Base TX Fiber Ethernet Media Converter System Design 4x 10/100Mbps TP ...
100M single fiber fiber ethernet media converter with external power supply he 10/100Base-Tx to 10...
Fiber Ethernet Media Converter 10/100Mbps RJ45 Duplex Fiber SC Port Converter Features • 10/100Base...
10/100M single fiber single mode fiber ethernet media converter 1. Description Media converter is 10...
IP30 Single-Mode SC Type Fiber Ethernet media converter 1310/1550nm Features In conformity to IEEE ...
10/100 Base-TX and 100Base-FX ethernet fiber optic media converter rj45 sc connector Features In ...