Active Member
|
[China]
Address: 6th Floor,NO. 8, Aobang Plaza, Rd 2nd, Wanggang Gongye Street， Baiyun District, Guangzhou
Contact name:Sindy Jin
GUANG ZHOU CITY FREESEA ELECTRICAL CO., LTD |
|
|
| Model | Voltage | HZ | Power(KW) | Power(HP) | Hmax(m) | Qmax(m³/h) | Port Size(inch/mm) |
| FL-150 | 220V-240V | 50/60 | 1.1 | 1.5 | 18 | 30 | 2.0/63 |
| FL-200 | 220V-240V | 50/60 | 1.5 | 2 | 19 | 35 | 2.0/63 |
| FL-300 | 220V-240V | 50/60 | 2.2 | 3 | 20 | 38 | 2.0/63 |
| FL-350 | 220V-240V | 50/60 | 2.6 | 3.5 | 21 | 40 | 2.0/63 |
| FL-400 | 380V | 50/60 | 3 | 4 | 22 | 48 | 2.0/63 |
Features:
1. Low virbration
2. Class F
3. Excellent performance
4. Big flow design
5. Ingress Protection: IP55
6. Stainless steel 304/316 weld shaft
7. Overload protection
8. Thermal protection
9. Fresh water/Sea water
Release all air from fitter and piping system: see filter owner manual
In a flooded suction system (water source higher than pump),
pump will prime.
it self when suction and discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove cap
cover; fill cap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace cap cover on cap turn clockwise to tighten cover.
PRIMING PUMP
NOTICE:
Tighten cap cover by hand only
Pump should prime now. Priming time will depend on vertical length
of suction lift and horizontal
of suction piping.
ROUTINE MAINTENANCE
The only routine maintenance is inspection/cleaning basket. Debris
or trash that collects in basket,
well choke off water flow through the pump. Follow instructions
below to clean basket:
Stop pump, close gate valve in suction and discharge, and release
all pressure from
system before proceeding.
1. Unscrew cap lid(turn counterclockwise).
2. Remove strainer basket and clean. Be sure all holes in basket
are clear, flush basket with water.
If basket is replaced backwards, cover will not fit on pre-filter
body.
3. Clean and inspect lid Ring: re-install on cap cover.
4. Clean Ring groove on pre-filter body and Replace lid. To help
keep lid from sticking, tighten
hand tight only.
5. Prime pump (see priming instructions above)
Description
This pump is ideal for pool pumping, cleaning, hot water circulation etc. Sometimes people use it for increasing the water pressure in the pipe, garden sprinkling, and irrigation. It only needs solar off grid power to get work! Delivery head of 14 meters and suction up to 8 meters. This pump is simple to install and easy to use. No need of sophisticated knowledge of pumping but just a little imagination of how much you can do with it. It will pump up the water in no time.
A smart pump controller packed with great specifications and features that make it perfect. Everything is made easy where it automatically switches your pump on/off on open/closing of any tap. It comes with a LED screen showing the live RPM, current, voltage, etc. It provides stable performance, requires low maintenance and is long lasting; it is one of the few that will exceed your expectations. Buy one today and have the best and most reliable equipment at hand.
STANDARD OFF CENTRE DISCHARGE: Pumps used on many spas from various spa manufacturers from 2000 onwards. Suitable for all types of spas including Salt, Chlorine, Bromine and Ozone Chlorination. Corrosion Resistant and Chemical-resistant thermoplastic body. Suitable for above ground and in ground spas. If used on a in ground spa and the pump is above the water level then select one of our self-priming pumps from our other listings. If center discharge is required then check our other listings.
