Active Member
|
[China]
Address: No.907,Jiuzhou Building,High-Tech Park,Nanshan, Shenzhen, China
Contact name:Yonchin Shou
Cabsat industrial limited |
|
|
Gigabit Dual-band omnidirectional built-in antenna 2.4G/5G Wifi Mesh Router CS-1000ME
MESH routing system CS-1000ME is a Gigabit dual-band home wireless networking suite product. Each node has a 10/100/1000Mbps WAN/LAN adaptive port, a 10/100/1000Mbps adaptive LAN port and a wireless transmission rate of 1167 Mbps.
| The device name | Mesh Wi-Fi | ||
| The device type | Mesh Wi-Fi (Table-Top) | ||
| The device model | CS-1000ME | ||
| WAN | 1*10/100/1000MWAN/LAN adaptive port | ||
| LAN | 1*10/100/1000MWAN/LAN adaptive port | ||
| WLAN | 2.4G 300Mbps,5G 867Mbps | ||
| Hardware Indicators | The main chip | RTL8197FS-VE5 | |
| Clock Speed | 1GHz | ||
| Flash Storage | 16MByte or Higher | SOP8 | |
| Ram Capacity | 128MByte or Higher | ||
| Power Specification | 12V1A | ||
| Light | A Comprehensive Light | (Red or yellow or green) | |
| Reset | Reset | ||
| Aerials | 2*3dBi | Dual-band omnidirectional built-in antenna | |
Wireless transmission rate
| 1167Mbps | ||
| Wireless Standards | 802.11b/g/n 2.4GHz； 802.11ac/a/n 5GHz； | ||
| Transfer Standards | 802.3；802.3u； | ||
| MESHNetworking standards | 802.11s； | ||
Roaming Standard
| 802.11v/r; | ||
| Category | Requirement | Standard |
Wired Interface | WAN ports | 1*10/100/1000 Base-T ports,It meets the IEEE802.3/802.3u standard supports full-duplex/half-duplex flow control. |
| LAN ports | 1*10/100/1000 Base-T ports,It meets the IEEE802.3/802.3u standard supports full-duplex/half-duplex flow control. | |
Power Interface | One power interface, router uses external power adapter to supply power. The external power adapter shall: 1. Meet the EMC requirements of YD/T 983 and pass CCC certification; 2. Input voltage: 198-242V-50Hz; 3. Output voltage DC: 12V (+5%), ripple range (+200mV), output current: 1A; 4. The MTBF time of power supply is more than 30000 hours. 5. The power interface of the equipment itself and the DC output interface of the power adapter should be a unified international standard circular interface with a diameter of 2.1 mm. 6. The DC output power supply line of the adapter can be equipped with EMI absorption magnetic ring. 7. Under normal conditions, the insulation resistance between the metal housing of the equipment and the power cord shall not be less than 50M. 8. There should be lightning protection and surge protection tests. The lightning protection level should be at least 1.5KV. | |
Wireless Interface |
Wi-Fi Wireless Network | It meets the standard of 802.11protocol,supports802.11b/g/n/a/ac,supports 2.4 GHz and 5 GHz,and has a wireless rate of 1167 Mbps. Two built-in 3dBi omnidirectional dual-band antennas; Up to 40 wireless devices are allowed. |
| Functional description | |
| System reset | Press the RST button for 6 seconds, release the indicator after flash, turn the indicator into long light and restart the system, and finally return the flashing indication to restore the factory settings successfully. |
| Indicator light | Green Long Bright: Good Connection Quality Yellow Long Bright: General Connection Quality Red Long Bright: Connection Failure |
LAN upstream devices should ensure the stability and reliability of hardware structure, antenna connection, etc. RAM is not less than 128 MByte, Flash is not less than 16 MByte.
