2.5KG 7.4V Tying Machine For Plants Tool Rechargeable Lithium Battery Plant Tying Tape

Plant Vine Tying Machine Vineyard Tool With 2 Pack Backup Rechargeable Lithium Battery

This Plant Tying Machine makes it easy to attach plants to support sticks. It is suitable for all kinds of plants, especially soft-stemmed vegetables and fruit trees. The Garden Tapener Tying Tool is small and exquisite, and it is very convenient to use. 4-5 times more plants can be bundled in a unit time than by hand.

Made up of manganese steel, durable pressure foot and make you hook straps more stable.
Adjustable Width: The opening width can be adjusted at any time depending on the width you need which make your work more convenient.

High Efficiency:

This Plant Tying Machine will greatly improve efficiency, save labor costs and save your time. It can quickly tie rattan plants and make crops grow better.

Easy Operation:

This Plant Tying Machine makes it easy to tie plants to sticks and lines. Garden Tapener Tying Tool will not damage plants. The maximum bundle diameter is 5cm.

Strong Support:

The Hand Tying Binding Machine is faster and more convenient than ordinary manual wire binding machines. It can work all day when fully charged.

Included Accessories:

The Electric Plant Tie Machine comes with a roll of grafting tape (3 meters), which effectively secures your plants and ensures the safety of valuable vines and trees.

Extensive Use:

Plant Tying Machine can be applied to various branches such as vegetables, grapes, tomatoes, cucumbers, peppers, flowers, eggplants, etc.

Specifications

Material: ABS+metal

Maximum bundle diameter: about 5cm/1.97

Tie wire: 3m long

Working voltage: 7.4V

Weight: about 800g

Packing list

1 x Electric Plant Tying Machine

1 x Tape (roll)

1 x Charger

Check the blade
►Before using the tool, check the blade for wear.
►Slow, worn blades can cause poor cuts, increase the difficulty of using the tool, and shorten its service life.
 

Adjust or replace the blade
CAUTION: The blade is very sharp, and the replacement or adjustment process must be very careful to avoid scratching your fingers.
►Press the handle slowly and check the upper and lower blades as normal, otherwise follow the method below.

1. Unscrew the inner hexagon screw with the attached hexagonal wrench；
2. Let the upper blade stick to the lower blade；
3. Re-tighten the inner hexagon screws.

►Make sure to use this thin washer when padded on some tool screws.
►When the upper blade is worn, follow the following method.
1. Remove the hexagon screw by using the attached hexagon wrench；
2. Remove the lock pin；
3. Remove the upper blade mounting seat；
4. Open the screw and replace the new blade；
5. After remounting the blade, install the blade.

Install the rope
CAUTION: The tool shall use the specified rope.Other ropes may cause failure to install, tie failure, and / or damage the tool.
►The rope attached with this tool can be used directly and is an example of rope installation and a real sample reference for the purchase of rope.
►If the tie rope is out of replacement, follow the method below.

1. Remove the loading plate in the back direction.

2. Pull out the loading plate between left and right.

3. Install the new rope into the loading plate and press the loading plate.

4. Install the rope head up into the tool and wear the rope through the handle and arm according to the figure above (dotted line).Improper installation of rope may cause failure to tie properly or pull out difficult.

5. Press the handle to cut off the front material of the rope.

OPERATION

1. Turn on the power switch and open the tool binding arm.

2. Place the things to be tied into the binding arm.

3. Press the handle and release to secure the front end of the rope to the lower blade.

4. Open the binding arm and remove the binding arm along with the rope.

5. Press the handle again to the end, and the blade cut off the rope and wrap the rope.After the handle is pressed to the bottom, it should be kept for about one second. Too short time may lead to unwinding and loose release; too long time may lead to the winding belt fracture and the binding failure.

6. Release the handle and tie complete.

Advantages:

1. Self-design and self-produce
2. Factory direct price
3. Keep product upgrading to meet market demand
4. According to customer's requirements to control costs and also satisfy the design requirements
5. Small orders welcome
6. Quick shipping within 10 days

Applicaton

This tool is suitable for loose fixation of wires.Such as the branches of plants and stent fixation, multilinear beam fixation, etc.

Other picture