14. RK-VFF30 Kit Includes:
1 GI-89 Gasket (15)
1 F1-10 Filter (13)
1 S7-3 Screen (12)
1 BD1-26* Diaphragm Assy (3)
2 S1-59 Screw, 8-32 x 5/8" (1)
2 S1-100 Screw, 12-24 x 5/8" (17)
1 S4-18 Seat (Viton/Aluminum)(19)
1 S3-116 Seal, Lip Pin (9)
1 PI-15 Pin, Valve Operating (10)
1 W1-42 Washer, Seal Retaining (14)
1 H1-14236 Seal Holder Insertion Tool
1 P1-14235 Pin Insertion Tool
1 PPI-128 Instructions
2 S1-15265-001 Screw, 8-32 17/32” Taptite Torx (1)
2 S1-15266-001 Screw, 12-24 x 11/16” Torxfil (17)
1 S1-15265-002 Screw, 8-32 3/8” Taptite Torx (4)
*Standard diaphragm. See table on page 2 for optional
diaphragms.
15. Lubricate the Lip Pin Seal (9) with petroleum jelly or Vaseline
and place in the Seal Holder Insertion Tool groove side up, as
shown in the illustration. Note that the Seal Holder passage is
tapered and the wide opening of the seal holder should be facing
up.
16. Place the VFF30 Body (7) with the filter side up, as shown in
the photo, on a flat surface. Ensure that the groove in the Seal
(9) is visible from the top of the taper of the Seal Holder
Insertion Tool.
![](http://img.everychina.com/nimg/f7/42/17e7f2b280eb94a1ebc8b2cd6f4c.jpg)
17. Place the holder in the up position and slide the Holder and
the Seal (9) into the Body (7) of the VFF30. Looking through the
fuel port, position the Seal abovethe cavity of the seal recess.
18. Coat the Pin Insertion Tool with petroleum jelly and push the
Seal (9) through the Holder and into the Seal recess of the VFF30
Body (7). Look through the fuel port to ensure the Seal is seated
in the seal recess and that the groove in the seal is visible.
19. Use needle nose pliers to hold the Seal Retainer Washer (14).
![](http://img.everychina.com/nimg/41/6a/50fd706de71b368d0f7d51170408.jpg)
20. Insert Seal Retainer Washer (14) in slot to hold the Lip Pin
Seal (9) in place.
21. Lubricate the Pin Valve (10) with petroleum jelly and insert
through hole in the Washer Retainer Seal (14) and Lip Pin Seal (9).
Rotate head of Pin gently in a circular motion to ease Pin into
place through the Washer, Lip Pin Seal and Body (7) housing.
22. Pin (10) properly placed in valve jet.
![](http://img.everychina.com/nimg/0c/ac/72adbb4dc97c2a604729f72bbd6f.jpg)
23. Valve Seat (19) shown with aluminum side up ready to be placed
on jet.
24. Place the Seat (19) with the viton (black rubber) side down, in
position on jet.
25. Spring (11) ready to be fastened in place. Be sure the arc in
the center faces upward (see illustration in step 26 below).
26. Replace Spring (11) and fasten in place with Screw (4). Align
the tip of Spring (over valve) and center between the 3 guide fins
as shown in illustration. Tighten Screw 28-32 in-lbs. (3.2-3.6 Nm)
27. When Spring (11) is in place, lift it slightly to ensure it can
move freely.
28. Insert Screen (12) and Filter (13) into recess.
29. Press Filter (13) so that’s properly seated in recess.
30. Place Gasket (15) in place and align with screw holes.
31. Insert two Screws (17) opposite each other in the “Fuel In”
cover and place on Gasket (15). Thread the two Screws (17) through
the gasket and into the Body (9).
32. Insert remaining 8 Screws (17) in their openings.
![](http://img.everychina.com/nimg/03/cc/7c0f04338bc276ad7d820e9c0cb9.jpg)
33. Tighten Screws (17), alternating from side to side on opposite
sides of the cover until all screws are solidly set. Torque to
60-70 in-lbs. (6.8-7.9 Nm).
34. Lift Lever (6) to ensure it moves properly and verify that the
Valve Pin (10) follows lever travel.
35. Turn Diaphragm (3) so the gasket side is down (see illustration
on page 2) place on the Body (7) and rotate to position so the
screw hole pattern aligns with the holes in the Body (there is only
one position in which the holes will line up).
36. Place Cover (2) in correct position and insert Screws (1).
37. Tighten Screws (1) alternatively from side to side across cover
until all are solidly fastened. Torque to 28-32 in-lbs. (3.2-3.6
Nm)
38. Pressurize the “Fuel In” opening with approximately 100 psi of
air pressure. Draw a soap bubble across the Lockoff outlet and
vacuum port (labeled “VAC”) to verify that no air is flowing
through either opening. If air escapes, the rebuild has failed and
the Lockoff must be replaced. Apply a small amount of vacuum to the
port labeled “VAC” to verify the air flows freely through the
outlet. Use soap and/ora commercial leak detector solution to
inspect the gasket seals around the perimeter of the Lockoff for
leaks. If leaks are found, the Lockoff must be replaced. If no
leaks are found, the Lockoff can be reinstalled and returned to
service