Active Member
|
[China]
Address: Room 403 Block A,Huafeng SOHO Creative World Hangcheng Industrial Zone Qianjin 2nd Road,Xixiang Baoan Shenzhen,China
Contact name:karen
Shenzhen Xinchenger Electronic Co.,Ltd |
|
|
System Printed Board High Frequency Rogers PCB Board Audio Amplifier Application In 0.79mm
Quick detail:
| Origin:China | Special: High frequency pcb |
| Layer:4 | Thickness:0.79mm |
| Surface: ENIG | Hole:0.2 |
Features:
1. Rogers pcb multilayer pcb with high frequency can improvide the
products quality ,with high techolonogy treatment improve the life
cycle of the products .Immersion gold surface finish make the pcb
's conductive performance enhancements. Multilayer pcb design ,the
precision of the pcb improves much more better . Low dielectric : 3
dielectric conductivity much more precision .
System Printed Board High Frequency Rogers PCB Board
Quick detail:
Material: Rogers 4350B 0.254MM 0.508MM
PP material Rogers 4450
Core: 3 or 4
Stack up files: Necessary
Gerber files:Necessary
System Printed Board High Frequency Rogers PCB Board The basic characteristics of a high frequency board material
requirements are the following:
(1) dielectric constant (Dk) must be small and very stable, usually
the smaller the better signal transfer rate and the dielectric
constant of the material
Inversely proportional to the square root of high dielectric
constant is likely to cause the signal propagation delay.
(2) the dielectric loss (Df) must be small, mainly affect the
quality, the smaller the dielectric loss signal transmission of the
signal loss is smaller.
(3) as far as possible consistent with the coefficient of thermal
expansion of the copper foil, copper foil separated because of
inconsistency will cause changes in the hot and cold.
(4) to low water absorption, high water absorption will affect the
dielectric constant and dielectric loss when damp.
(5) Other heat resistance, chemical resistance, impact strength,
peel strength, etc. must also be good.
Typical Applications:
System Printed Board High Frequency Rogers PCB Board Rogers high frequency pcb widely used in the area of high technologies like communication device,Electronics,Aerospace,Military industry and so on. we have accumulated abandunt experiences in the line of high frequency microwave business for which widely apply to power divider,combiner,power amplifier,line amplifier,base station,RF antena,4G antena etc.
We have sufficient rogers material raw as follow:RO4003C,RO4350B,RO4360,RO4533,RO4535,RO4730,RO4232,RO4233,RO3003,RO3006,RO3010,RO3035,RO3203,RO3206,RO3210,RO3730,RO5780,RO5880,RO6002,RO3202,RO6006,Frequently-used is 4003C,4350B,5880
So we can do pcb circuit board with your detail requirements in the case of you send us gerber files or any other files
Parameter:
| o | Item | Data |
| 1 | Layer: | 1 to 24 layers |
| 2 | Material type: | FR-4, CEM-1, CEM-3, High TG, FR4 Halogen Free, Rogers |
| 3 | Board thickness: | 0.20mm to 3.4mm |
| 4 | Copper thickness: | 0.5 OZ to 4 OZ |
| 5 | Copper thickness in hole: | >25.0 um (>1mil) |
| 6 | Max. Board Size: | (580mm×1200mm) |
| 7 | Min. Drilled Hole Size: | 4mil(0.1mm) |
| 8 | Min. Line Width: | 3mil (0.075mm) |
| 9 | Min. Line Spacing: | 3mil (0.075mm) |
| 10 | Surface finishing: | HASL / HASL lead free, HAL, Chemical tin, Chemical Gold, Immersion Silver/Gold, OSP, Gold plating |
| 11 | Solder Mask Color: | Green/Yellow/Black/White/Red/Blue |
| 12 | Shape tolerance: | ±0.13 |
| 13 | Hole tolerance: | PTH: ±0.076 NPTH: ±0.05 |
| 14 | Package: | Inner packing: Vacuum packing / Plastic bag,Outer packing: Standard carton packing |
| 15 | Certificate: | UL,SGS,ISO 9001:2008 |
| 16 | Special requirements: | Buried and blind vias+controlled impedance +BGA |
| 17 | Profiling: | Punching, Routing, V-CUT, Beveling |
Features
• High Thermal Performance
Tg: 180°C (DSC)
Td: 340°C (TGA @ 5% wt loss)
Low CTE for reliability
• T260: 60 minutes
• T288: 30 minutes
• RoHS Compliant
• UV Blocking and AOI Fluorescence
High throughput and accuracy during PCB
fabrication and assembly
• Superior Processing
Closest to conventional FR-4 processing
• Core Material Standard Availability
Thickness: 0.002″ (0.05 mm) to 0.125″
(3.2 mm)
Available in full size sheet or panel form
• Prepreg Standard Availability
Roll or panel form
Tooling of prepreg panels available
• Copper Foil Type Availability
Standard HTE Grade 3
RTF (Reverse Treat Foil)
• Copper Weights
½, 1 and 2 oz (18, 35 and 70 μm) available
Heavier copper available upon request
Thinner copper foil available upon request
• Glass Fabric Availability
Standard E-glass
Square weave glass fabric available
Spread glass fabric available
• Industry Approvals
IPC-4101C /21 /24 /26 /97 /98 /99 /101 /126
UL - File Number E41625 as PCL-FR-370HR
Qualified to UL's MCIL Program
PrePreg Material
| Parameter | Value |
| Specific gravity/density | 1.850 g/cm3 (3,118 lb/cu yd) |
| Water absorption | −0.125 in < 0.10% |
| Temperature index | 140 °C (284 °F) |
| Thermal conductivity, through-plane | 0.29 W/(m·K), 0.343 W/(m·K) |
| Thermal conductivity, in-plane | 0.81 W/(m·K), 1.059 W/(m·K) |
| Rockwell hardness | 110 M scale |
| Bond strength | > 1,000 kg (2,200 lb) |
| Flexural strength (A; 0.125 in) - LW | > 440 MPa (64,000 psi) |
| Flexural strength (A; 0.125 in) - CW | > 345 MPa (50,000 psi) |
| Tensile strength (0.125 in) LW | > 310 MPa (45,000 psi) |
| Izod impact strength - LW | > 54 J/m (10 ft·lb/in) |
| Izod impact strength - CW | > 44 J/m (8 ft·lb/in) |
| Compressive strength - flatwise | > 415 MPa (60,200 psi) |
| Dielectric breakdown (A) | > 50 kV |
| Dielectric breakdown (D48/50) | > 50 kV |
| Dielectric strength | 20 MV/m |
| Relative permittivity (A) | 4.8 |
| Relative permittivity (D24/23) | 4.8 |
| Dissipation factor (A) | 0.017 |
| Dissipation factor (D24/23) | 0.018 |
| Dielectric constant permittivity | 4.70 max., 4.35 @ 500 MHz, 4.34 @ 1 GHz |
| Glass transition temperature | Can vary, but is over 120 °C |
| Young's modulus - LW | 3.5×106 psi (24 GPa) |
| Young's modulus - CW | 3.0×106 psi (21 GPa) |
| Coefficient of thermal expansion - x-axis | 1.4×10−5 K−1 |
| Coefficient of thermal expansion - y-axis | 1.2×10−5 K−1 |
| Coefficient of thermal expansion - z-axis | 7.0×10−5 K−1 |
| Poisson's ratio - LW | 0.136 |
| Poisson's ratio - CW | 0.118 |
| LW sound speed | 3602 m/s |
| SW sound speed | 3369 m/s |
| LW Acoustic impedance | 6.64 MRayl |
Rogers material in stock:
| Brand | Model | Thickness(mm) | DK(ER) |
| F4B | F4B | 0.38 | 2.2 |
| F4B | 0.55 | 2.23 | |
| F4B | 0.225,0.3,0.5,08,1,1.2,1.5,2,2.5,3.0 | 2.65 | |
| F4Bk | 0.8,1.5 | 2.65 | |
| F4B | 0.8 | 3.5 | |
| FE=F4BM | 1 | 2.2 | |
| Rogers | RO4003 | 0.254 0.508,0.813,1.524 | 3.38 |
| RO4350 | 0.254 0.508,0.762,1.524 | 3.5 | |
| RO5880 | 0.254.0.508.0.762 | 2.2 | |
| RO3003 | 0.127,0.508,0.762,1.524 | 3 | |
| RO3010 | 0.635 | 10.2 | |
| RO3206 | 0.635MM | 10.2 | |
| R03035 | 0.508MM | 3.5 | |
| RO6010 | 0.635MM, 1,27MM | 10.2 |
Competitive Advantage:
1) With UL,ROHS,ISO,IPC
2).Lead time:3-10 working days
3)Competitive price best quality
4).Rich 20 years experience in High Tg Multilayer PCB .
What Information customer need to provide for quotation ?
1. PCB Gerber files ,protel,powerpcb,Autocad,etc.
2. BOM list for PCB assembly.
3. Send us your sample PCB or PCBA.
4. OEM is acceptable.
Company Service:
24 hours quick sample is avaliable here.
reply Customer's any enquiry within 3 hours;
Blind buried hole ,crossed blind hole can be done
24 hours Engineering Gerber files treatment.
24 hours English Engineering Questions Confirmation by E-mail.
Supply the best project fit for production customized
