|
[China]
Trade Verify
Address: i City, No11, TangYan South road, Yanta District, Xi'an,Shaanxi,China.
Contact name:Evelyn Wang
Xi'an Kacise Optronics Co.,Ltd. |
|
Verified Suppliers
|
|
|
KUS600 series ultrasonic transmitter
Unit in the diagram is mm.
| Cable color | Pin | Description | Note |
| Red | 1 | Power supply | |
| Black | 2 | GND | |
| Yellow | 3 | Analogue output | The 600B will work in mode 1 or 0 cannot work in power save mode, if the 4-20mA, 0-3.3V 0-5V analogue output used. |
| Blue | 4 | RS485A+ | TTL-TXD for ttl output signal |
| Green | 5 | RS485B- | TTL-RXD for ttl output signal |
For switch output
| Cable color | Pin | Description | Note |
| Red | 1 | Power supply | |
| Black | 2 | GND | |
| Yellow | 3 | Switch output | Load current 1A@60V |
| White | 4 | Switch output | |
| Brown | 5 | RS485A+ | TTL-TXD for ttl output signal |
| Green | 6 | RS485B- | TTL-RXD for ttl output signal |
General specifications
600B
| |
| Sensing range | 600... 5000 mm@3.3V power supply. The measure distance can reach 6 meters if the power supply is 24V. |
| Adjustment range | 300….5000mm |
| Unusable area | 0 ... 600 mm |
| Response delay | approx. 10 ms |
Electrical specifications
| Operating voltage UB | 3.3 ... 24 V DC , ripple 10 %SS |
| No-load supply current I0 | ≤ 20 mA active period and ≤0.3mA during sleep time |
The detail refers to the 600B software engineer application guide.
Adjusting the analogue output.
The analogue output can be programed as the user want. Such as working at switch output or working at liner output all the parameters can be set by the RS485 interface.
There is 8 types of output functions can be programed.
All the setting routine as follows,
step 1 set one pointed distance by the RS485,
step 2 set another pointed distance by the RS485.
Step3 set the output type liner or switch, and set the related output options
Step4 reboot the sensor.
1. Window mode normally-open and liner mode positive slope output function.
2. Window mode normally-closed and liner mode negative slope output function.
3. Single switching point, normally-open function.
4. Single switching point, normally-closed function.
5. Single switch point with hysteresis gap normally-open function.
6. Single switch point with hysteresis gap normally-closed function.
7. Detection of object presence-normal open function.
8. Detection of object presence-closed open function.
Switching point, Setting distance only after power on. The internal clock can assure can't be changed after 5 minutes after power on. If want to change the switching point, the user can only setting the request distance after power restart.
For the RS485 output type.
There are 2 kinds of working style,
One for auto measure, the sensor will measure the distance or level repeatedly, and the measurement period can be set by the UART. The measure result can be fetched every time.
The other style is power save mode when the sensor is sleep, until the sensor received the inquiry command with pre-code. Communication protocol is Modus-RTU.
For example the measure result can be read by access the register 0x101 by Modbus protocol.
For more information please contact us for the software engineering guide.
If the sensor is installed at the environment temperature fall below 0℃,It should do well on the protective measures. In case of direct mounting of the sensor in a through hole using the steel nuts, it has to be fixed at the middle of the housing thread.
6. Ordering information
| KUS | Body size | OUTPUT | Max range | Description |
| 600 | ||||
| Customized | Customized | |||
| SW | Switch Output (online configurable for NPN or PNP) | |||
| mA | 3 wire 4-20mA output | |||
| 10V | Output is Vout 0-10V | |||
| 5V | Output is Vout 0-5V The power supply range is 5.0 at least | |||
| 3.3V | Output is Vout 0-3.3V The power supply range is 3.3 at least | |||
| RS485 | Output is RS485 | |||
| TTL | UART TTL output | |||
| XXX mm | Xxx mm is the maxim range can be detected, the default length is 1 meter | |||
| KUS | 600 | RS485 | 5000mm | |
