Active Member
|
[China]
Address: C&F INDUSTRIAL ZONE, CAIDIAN,WUHAN,CHINA
Contact name:Fan CHEN
Hubei EverFLON Polymer Co.,Ltd |
|
|
PTFE Non Stick Coating / Three-Layer Spray / Water Base Non-Stick Coatings
TFE anti-stick and non stick coating
1. Abundant experience and factory directly
2. Customized
3. Quality and service assurance
4. Process materials supplied by clients
Coating material:
Peek, PTFE, PFA, FEP, ETFE, ECTFE, etc
Coating thickness:
0.01mm-1mm based on clients’ requirement
Product description
Ptfe Coating Advantages:
1. Abrasion resistance
2. Self lubrication
3. Corrosion resistance
4. No adhesion
5. Scratch resistance
6. High temperature resistance
7. Electrical insulation
8. No-toxic
9. Ageing resistance
Note: Different coating material will have different advantages. Also need to consider your basic materials.
So pls kindly send your need detailed function or finished coating sample, then we will give you best suggestions.
Brief Introduction
Techyours® is designed with two-layer coating system. Thanks to its high density, good inadhesion, easy-to-clean performance and strong practicability. It is applicable for substrates like aluminum, alloy and stainless steel etc.
Type of PTFE Coating
Water Base
Main Features of PTFE Coating
l Eco-friendly
l Excellent heat resistant
l Excellent chemical resistance and abrasive resistance
l Excellent and lasting non-stick performance, easy to clean
Data List of Techyour PTFE Coating
| ITEM | 16700 |
|---|---|
| Appearance | Black liquid |
| Solid content (%) | 35±1 |
| Viscosity (cp) | 600~1000 Primer 400~800 Top |
| Density (g/ml) | 1.20 Primer/1.30 Top |
| pH | 8-11(Primer and top) |
| Color of the film surface | 8-11(Primer and top) |
| Curing temperature (℃) | 380-420 |
| Gloss (60° glossimeter) | 10-20 |
| Film thickness (μm) | 20-30 |
Non-stick performance Fry eggs at 170±10℃ | >10 cycles |
Corrosion resistance Boling 10% salt water for 24 hours | No blister |
| Abrasion resistance 3KG/21cm2 | >3000 cycles |
| Hardness (ZHONGHUA pencil) | >H |
Main Processing Way of Techyour PTFE Coating
1. Requirement on pre-treatment
l Firstly, apply high-temperature degreasing, then wash with 1%~3% NaOH solution (60℃) for more than 6 minutes, dry it after water rinsing;
l Blast with 80#~120# corundum to make the surface roughness reach 2.0μ~3.0μ, pay attention to sandblast evenly;
l Wash with 1%~3% NaOH solution(60℃) for more than 6 minutes, rinse with water;
l Wash with 1%~3% hydrochloric acid solution (60℃) for more than 6 minutes, rinse with water and dry.
2. Preparation of the coating
l Dispersion of coating: the coating must be fully dispersed before operation;
l Viscosity adjustment: the viscosity could be adjusted according to different spray methods. Dilute with clean water if the viscosity is over high;
l Coating filtration: filtrate the coating with screen (100mesh) before using.
3. Application
l The spraying environment should be dry, well-ventilated, no smoking and fire. We suggest using dedicated spray gun, elevated tank and curing oven;
l The air compressor should be degreased, dewatered and equipped with water oil separator before using;
l Roll the coating at 30rpm speed before using to make sure there is no sediment, and filter with 100 mesh screen;
l Adjust atomization and oil pump capacity of the spraying gun; make sure the unit is clean and flat;
l Preheat the substrate to 35℃ and spray the primer. Dry it at temperature of 120℃~150℃ for 10min-15min. Keep the thickness of primer within 12μm-18μm;
l Spray top coating after the primer is dry and cooling to room temperature, then spray the top. Dry the unit at the temperature of 100℃~150℃ for 10~20 min, and gradually increase the temperature to 380℃~420℃. Keep for 10 min. Keep the thickness of top coat within 10μm~12μm. The thickness of two coat tally should be between 20μm~30μm;
l The oven (or the tunnel drier) must be well ventilated; otherwise, it will lead to color change of coating.
Main Application of Techyour PTFE Coating
l Ecofriendly PTFE emulsion
l Non-stick and excellent abrasion resistant
l Excellent weatherable, salty foggy resistant
l Excellent strong acid resistant and alkali resistant
l Applied to iron, aluminum, ceramic, stainless steel cookware etc.
Package&Delivery
Techyours® PTFE non-stock coating must be stored under frost proof
environment under optimum 18-26℃ temperature;
It should be homogenized once or twice a month by gentle rolling or
stirring when storing or before using,90min per time.
Techyours® PTFE non-stock coating is package in 25L PE drum with
25kg(55lb) content.
Before processing, please read the Materials Safety Data Sheet carefully. You could find them from www.everflon.com, or contact us +86-27-84888055 or our local service center, you also should could scan the QR code which on the package to download by your Smartphone.
