Active Member
|
[China]
Address: Rm. 3306, Int'l Tech Bldg., No. 3007, Shennan Middle Road, Shenzhen, Guangdong, China
Contact name:Tina
Shenzhen Topmay Electronic Co., Ltd. |
|
|
Yellow Box Type Metallized Polyester Film Capacitor 22uF 100V For Filter
Features
Box Type Provides the identical outer appearance.
Wide Capacitance range, small size
Long Life due to self-healing effect.
Suitable for block, by-pass and coupling of DC and signal to VHF range.
Widely used in filter, noise supression and low pulse circuits
Configuration
Non-inductive, wound with metallized polyester film as dielectric and electrode, copper-clad steel leads and encapsulated in a plastic case sealed with epoxy resin.
Specifications:
| Referance Standard | GB/T7332-1996 | |||||||||||||
| Climatic Category | 40/85/21 | |||||||||||||
| Rated Voltage | 100V | |||||||||||||
| Capacitance Range | 22uF | |||||||||||||
| Capacitance Tolerance | ±10%(K) | |||||||||||||
| Voltage proof | 1.6UR(5s) | |||||||||||||
| Dissipation Factor | ≤0.1%(20℃, 1KHz) | |||||||||||||
| Insulation Resistance | ≥15000MΩ (CR≤ 0.33 uF) ≥5000S (CR≥0.33 uF) (20℃,1min) | |||||||||||||
Dimensions
| Item | W(mm)±1.0 | H(mm)±1.0 | T(mm)±1.0 | P(mm)±1.0 | |||||
| TMCF06-226K100VP27.5B | 32 | 28 | 18 | 27.5 |
Packing:
Bulk
Part Number System
OUTSIDE MARKS FOR CAPACITANCE:
| PF | 100 | 1000 | 10000 | 100000 | 1000000 |
| NF | 0.1 | 1.0 | 10.0 | 100.0 | 1000.0 |
| μF | 0.0001 | 0.001 | 0.01 | 0.1 | 1.0 |
| Code | 101 | 102 | 103 | 104 | 105 |
TEST CONDITION
| Dash | Item | Test Conditions | Requirement | ||||||
| 1 | Tolerance | Frequency:1KHZ ±0.1KHZ ce:≤1Vrms | ±5%(J)±10%(K) | ||||||
| 2 | Dissipation | Frequency:1KHZ ±0.1KHZ Test Voltage:≤1Vrms | ≤1% | ||||||
| 3 | Insulation Resistanc | Insulation Resistance:10V±1V Temperature :20℃±15℃ Test Time:60±5sec | C≤.33UF CR≥15000MΩ C≥.33UF IR*C≥5000S | ||||||
| 4 | Withstanding Voltage | Leads : 1.6UR for 5sec Leads & Case: 2UR for 5sec | No breakdown or flashover | ||||||
| 5 | Suitability to Variable Temperatures | Temperature :θA=-55℃,θB=+85℃ Duration for each climate:30min Interval:2～3min Test Times:5 times | No visible damage Δc/c≤5% tgδ≤1.0% | ||||||
| 6 | Lead Tensile Strength | Lead Tension:
| No mechanical damage, such as leads breakage, loose. | ||||||
| 7 | Wire bending strength | (Half of leads uncovered),Pressure:
Continously bent twice to both opposite directions at angle of 90 ° | No mechanical damage, such as leads breakage, loose. | ||||||
| 8 | Weldability | Solder temperature:235℃±5℃ Solder time:2.0±0.5sec Solder:Green material(Pb-free) Flux:25/75(Rosin / spirits) | 90% of tin in surface | ||||||
| 9 | Wet Soldering Method | Wet Soldering Method Solder at 260±5℃ Soaking time:10±2sec Insulation plate thickness:1.5±0.5mm | c/c≤2% No visible damage | ||||||
| 10 | Vibration | Frequency:100～500HZ Direction and Time:2h for each of three different directions Amplitude: 0.75mm: During 30 min of each test at one direction, do electrical tesst for step contact, open or short . | No visible damage; No step contact last for or over 0.5ms; no open or short case | ||||||
| 11 | Damp Heat | Temperature:40±2℃ Relative Temperature:90～95% Voltage Condition:Rated Voltage Lasting Time:500h Capacitors need be at standard atmospheric pressure for 1~2 hours before test | No visible damage ΔC/C≤5% tgδ≤1.0% C≤.33UF CR≥7500MΩ C≥.33UF ≥2500S |
FAQ Of Topmay Capacitor
1) Can I have a free sample to test ?
Yes, we could provide free samples to test and check quality.
Freight cost is collected.
2) What is the lead time?
Sample needs about 7~10 working days prepared; mass production
average time takes 15-20 working days
3) Do you have any MOQ limit?
Yes. But it depends on product. Normally MOQ is 2K~10Kpcs
4) How about price terms?
We do FOBSHENZHEN if order amount is more than 5000USD. Less than
that, it is EXWSHENZHEN and we do not undertake local charge.
5) What information should I let you know if I want to get a
quotation?
Basically for capacitor, it requires to know detailed capacitance and voltage. If you have more information, such as type, product photo for reference, you could kindly provide too.
