A356 Investment Casting Aluminum Parts At Home Adc12 Small Auto Spare Custom

Auto Spare Investment Casting Adc12 Die Cast Aluminum Parts Cast Aluminum Products Permanent Mold Casting
 
Basic Information

 
Product Display
 

 
 

Aluminum casting material

There are two types of aluminum logs, primary and secondary. It is mainly composed of pure aluminum, and it is mainly composed of raw materials and scraps. There are three components used to make secondary aluminum when the furnace is charged: raw material, scrap, and hardener. Bonnell Aluminum's Carthage, Tennessee and Newnan, Georgia foundry facilities manufacture secondary logs. However, all billets/logs are within the specifications of the Aluminum Association.

Primary aluminum: 99.9% pure aluminum. There are three forms of primary aluminum purchased: T-bar, aluminum billet / aluminum block, aluminum ingot

Over fifty pounds of T-bar, billet/block

Aluminum ingots weighing less than 50 pounds

Primary aluminum is also classified by iron content,

Scrap: Materials purchased from external sources and materials generated within a factory.

Hardener: Elements are added to the aluminum bath to increase strength and impart properties to the final product such as finish, strength and grain refinement. The elements are as follows: silicon (Si), iron (Fe), copper (Cu), manganese (Mn), magnesium (Mg), chromium (Cr), zinc (Zn), titanium (Ti) and boron). Silicon, iron, copper, manganese, magnesium, chromium and zinc are used to increase strength and improve finish. Titanium and boron are used for grain refinement, which is a reduction in grain size, resulting in more consistent grains and better extrudability.

Preparation preparation

The first step in adding the furnace is to add the right amount of alloying agent: scrap, raw material and hardener. A charge is a mixture of raw materials that are melted and mixed to make the alloy. Raw materials and waste are first added to the furnace. The cast alloy determines the amount of scrap and raw material used to charge the furnace. Raw materials and waste are preheated to remove moisture, which will cause an explosion.

Aluminium

To calculate how much material you need to add to the furnace, you must first know how much healing is left from the last drop of the furnace. A healing is the remaining metal left in the furnace after a heat has been completed. A drop is the act of pulling a pin in the furnace and allowing the aluminum to flow into the pot until the formation of the log is complete. The formula for calculating how many pound primes to add is:

Prime (lbs) = [Charge (lbs) - Heal (lbs) ] * [Target's Prime]

Once the raw material is melted, place the scrap in the furnace until the furnace is full and allowed to melt. Aluminum has a melting point of 1215 degrees Fahrenheit.

Degassing / Fluxing

Degassing is the removal of hydrogen from molten metal by passing a gas mixture up the melt. Flux is a substance that promotes fusion, especially of metals or minerals. Flux can cause impurities such as alkalis, sodium and lithium (resulting in poor material surface finish) to rise to the surface of the bath. Once degassing is complete, sample and analyze for appropriate chemical composition.

Scum is a mixture of alumina and non-metallic materials that float on the surface of molten aluminum. When aluminum is added to an already painted, anodized or dirty furnace, dross is created. The dross falls off the top of the molten aluminum into the dross pan. The dross was cooled with argon to eliminate oxygen from the mixture and prevent the mixture. Heat is the temperature at which aluminum will burn. Recycling dross to recover aluminum from it.

Add hardener

Photograph and analyze samples using a spectrometer. A spectrometer determines the concentration of alloying elements by comparing the relative intensities of the wavelengths produced when the sample is irradiated with an electric spark. Hardeners such as silicone and magnesium are added to bring the alloying agent concentration to the specifications of the alloy being cast.

mold casting

The temperature of the metal must be between 1300-1340 degrees Fahrenheit, the analysis must be within the specified range, and degassing must be complete before the descent can begin. The casting process used at Bonnell Aluminum is called direct cooling casting because cooling of the log occurs in the mold itself, through which water flows. After all the criteria have been completed, the descent can begin. Safety equipment must be installed before firing the furnace. Tapping is the process of pulling the plug pins out of the stove so the aluminum can flow into the slots and pans.

Certificates and Honors
 

 
Factory display
 
 
 
 
 
Company Profile
 
Jiangyin Longkang Metal Products Co., Ltd. is located in Zhouzhuang Town, Jiangyin City - the largest aluminum extrusion profile production base. Covering an area of more than 35,000 square meters with more than 350 employees. We focus on metal customization, special-shaped aluminum profiles, aluminum profiles, aluminum tubes, rail transit series, doors and windows aluminum profiles, heat sinks, CNC processed aluminum profiles, interior decoration series, bending series, etc. We also have precision anodizing and various surface treatments, such as PVC film, wood grain, electrophoresis, powder coating, anodizing, etc. After more than 20 years of development, The company has become a modern aluminum production enterprise with perfect quality management system.
 
The company has the ability to develop and design molds independently, we can produce any extruded aluminum profiles according to your mechanical drawing or sample. Longkang has 10 extrusion production lines (600-3500 tons), one automatic oxidation electrophoresis production line, vertical and horizontal spraying production line per each, and a variety of advanced supporting production, processing and testing equipments. There are also CNT digital control drilling and milling machine(CNC), double head saw, hydraulic saw and punching machine in our processing workshop. The complete technological process can benefit to reduce the production turnover times for semi-finished products, to avoid the damage during transportation, improve the production efficiency, reduce the cost of production,and to ensure the quality and delivery time.
 
Efficiently treating our customers as partners with sincerity, specialization and satisfaction is our managerial principle. Attributed to the backup of a dedicated technical team, filled with wide and profound knowledge and practice in aluminum profile and world trade for 20 years, the company owns rich experience in product quality control and profile physical properties such as Hardness, Stretchability, Flatness, Straightness, and Tolerance etc. In line with the principle of sharing the preferential cost and joint development, the company has formed an interest community for years with its customers at home and abroad. Sincerely to build up a pleasant mutual trust, cooperative, win-win and value-added sustainable partnership is what we are achieving to grow together with you!
 
FAQ
Q: How long can I receive the goods after placing the order?
A: 15-30 working days after receiving the deposit (depending on the quantity).
 

Q: What is the thickness of the anodizing? Can you do 12um?
A: Our normal thickness is about 10 um. Yes, we can do 15 microns and above.

Q: What colors can powder coatings be used for? The thickness of the powder coat?
A: We can do any color for powder coating as long as you can provide color samples. Our usual powder coating thickness is 60-80um.