Combined Ring Wave Lightning Surge Generator 6KV Meet the
Requirements of IEC61000-4-12
1. Introduction:
Ring wave generator is completely meet the requirements of
IEC61000-4-12, GB/T17626.12 and ANSIC62.41/45.Ring wave generator
is used for the simulating electrical network, the power supply of
the reactive load the control line switch, as well as sensing the
ring wave of the low voltage cables terminal equipment caused by
the disconnection of the power circuit, fault and insulation
breakdown or lightning stroke. It is widely used in electronic
equipment.
Surge generator is designed according to IEC61000-4-5 and
GB/T17626.5,and completely meet the requirements of the standards.
It is widely used in the fields of industry control equipment,
house-holding appliance,medical electronics, communications
electronics,components, auto control equipment and etc.
2. Standard:
IEC61000-4-12 GB/T17626.12, ANSI C62.41/ 45, IEC61000-4-5 and
GB/T17626.5
3. Features:
1. 7 inches LCD touch screen, with plentiful functions, easy to
operation and update the software.
2. User can design the test program, and has 1000 groups memories.
3. Monitoring the surge voltage and current waveform by work with
an external oscilloscope.
4. Built in single phrase 10A (16A) network, makes the equipment
smaller and convenient.
5. With high-strength plug in the panel, EUT can connect with the
equipment convenient and reliable.
6. Monitoring the work voltage and current of the EUT. Overvoltage
protection and overcurrent protection.
7. Intelligent test the surge output, warning at voltage error and
no output.
8. Intelligent judge the abnormal of high voltage and surge output.
4. Parameters of Ring Wave Generator:
Voltage Oscillation frequency (open): | 100kHz±10% |
Output voltage(open): | (250V~4000V)±10% |
Frontier(open circuit voltage,T1,10%~90%): | 0.5μs±30% |
Frontier(short circuit voltage,T2,10%~90%): | ≤0.9μs |
Decay Rate (open circuit voltage) | 40%<(PK2)/(PK1)<110% |
40%<(PK3)/(PK2)<80% |
40%<(PK4)/(PK3)<80% |
Short circuit current at 3500V(PK1): | 292A±10% @12Ω |
117A±10%@30Ω |
Interval: | 1s~99s |
Impulse times: | 1~9999times |
Output mode: | Positive, negative, positive/negative auto |
Output Impedance: | 12Ω,30Ω |
Phrase: | asynchronous, synchronous |
Coupling and decoupling network(CDN): | 16A single Phrase or 20A 2phrases/5wires |
5. Parameters of Surge Generator:
Output voltage (open) | 6kV (Max) ±5% |
Front time | 1.2μs ±30% |
Time to half-value | 50μs ±20% |
Output current (short) | 3kA (Max) ±5% |
Time to half-value | 20μs ±20% |
Output polarity | Positive, negative, positive/negative automatically |
Output impedance | 2Ω±10% |
Synchronization,asynchronization | Synchronization,asynchronization |
Inject phase | Freely set at 0-360°,resolution:1° |
Trigger mode | Auto or manual, single |
Surge times | 1-9999 times |
Memories | 1000 groups |
Surge interval | 20-9999s |
Accuracy: | 5% |
CDN | AC:single phrase 300V,10A (16AMax), 50/60Hz |
| DC: 300V, 10A (Max) |
Working environment | Temperature:15°C-35°C humidity:0%-75% |
EUT power supply | AC220±10%, 50/60Hz, about 300W |
Dimension | W470mmxH260mmxD500mm |
Weight | About 35kg |