|
[China]
Trade Verify
Address: No55. Jiucaiyuan road, Furong District, Changsha, Hunan,China
Contact name:Ling Bo
Changsha Sollroc Engineering Equipments Co., Ltd |
|
Verified Suppliers
|
|
|
Rock Breaking Equipments SRC531 RC Drilling Bits For Water Well Drilling
Basics of Reverse Circulation Drilling:
(1) RC drilling uses rods with inner and outer tubes, the drill
cuttings are returned to surface inside the rods. The drilling
mechanism is a pneumatic reciprocating piston known as a hammer
driving a tungsten-steel drill bit.
(2) RC drilling utilizes much larger rigs and machinery and depths of
up to 500 meters are routinely achieved. RC drilling ideally
produces dry rock chips, as large air compressors dry the rock out
ahead of the advancing drill bit.
(3) RC drilling is slower and costlier but achieves better penetration
than RAB or air core drilling; it is cheaper than diamond coring
and is thus preferred for most mineral exploration work.
(4) Reverse circulation is achieved by blowing air down the annulus of
the rod, the differential pressure creating air lift of the water
and cuttings up the inner tube which is inside each rod. It reaches
the deflector box at the top of the drill string then moves through
a sample hose which is attached to the top of the cyclone.
The drill cuttings travel around the inside of the cyclone until
they fall through an opening at the bottom and are collected in a
sample bag. For any drill hole there will be a large number of
sample bags, each one marked to record the location and drilling
depth that the sample was obtained.
The collected series of sample bag cuttings are later taken for
analysis to determine the mineral composition of the drill hole.
The analysis results of each individual bag represents the mineral
composition at a particular sample point in the drill hole.
Geologists can then survey the drilled ground analysis and make
decisions about the value of the overall mineral deposit.
Features of SOLLROC RC hammer and bit:
-Spare parts are made of quality raw material with carburized treatment offer good wear resistance.The hammer achieve excellent wear resistance and high penetration rate
-Various selection for bit head shape,button shape and button configuration.It can completely satisfy the customization requirement and have adaptability to varies of conditions.
-Rc bit is interchangeable with well-known brand shank.The interchangeable shank design helps customers to optimized inventory.
Shank can be available:
1). RC bits for 3" RC Hammer: Diameter(86mm-102mm), shank type:
SRC531,
2). RC bits 3.5" RC Hammer: Diameter(98mm-115mm), shank type:SRC3.5
3). RC bits 4'' RC Hammer:Diameter (104mm-127mm), shank type:
SRC004
4). RC bits 4.5'' RC Hammer:Diameter(113mm-135mm), shank type:
SRC542,SRC543
5). RC bits 5" RC Hammer: Diameter(122mm-142mm), shank type:
SRC545,SRC040,SRC004
6). RC bits 5.5" RC Hammer: Diameter(133mm-146mm), shank
type:SRC547, SRC054,SRC052,SRC054
Test Data of RC Drilling Tools
| Rock formation | Drilling meters |
Huni Sandstone, Banket Sandston, Banket Conglomerate, Tarkwa Phylite, Mafic, Kawere (Dolerite) in Ghana | 160m averagely |
| Iron ore, spodumene, granite, basalt, oxide in Western Australia | 1000m-3000m |
3 inch RC Hammer, SRC531 RC hammer
| Item | Bit Dia(mm) | Bit Dia(inch) | Weight (kg) | Hole range | Working Pressure |
| SRC531 | 81mm | 3" | 29.0kg | φ84-φ100 | 1.0-2.5Mpa |
3 inch Drill bit, SRC531 Bit
| 3" shank Bit | Bit Dia(mm) | Bit Dia(inch) | Air Hose | Gauge buttons | Front buttons | Part No |
| 86 | 3 3/8" | 2 | 6×φ12 | 5×φ12 | SRC531-86 |
| 89 | 3 1/2" | 2 | 8×φ12 | 5×φ12 | SRC531-89 | |
| 95 | 3 3/4" | 2 | 8×φ12 | 6×φ12 | SRC531-95 | |
| 102 | 4" | 2 | 8×φ12 | 6×φ12 | SRC531-102 |
1) Non-Blocking:Our RC hammers are proved to ensure extremely low
rate of blocking during it works.
2) High Efficiency:The well drilling equipment carries with larger
power of impact frequency and torque, thus ensuring faster
penetration. Compared with others, the efficiency can be improved
10%.
Our Service:
1.Pre-sale service:
Act as a good adviser and assistant of clients enable them to get
rich and generous returns on their investments .
(1)Select equipment model.
(2)Design and manufacture products according to customer‘s needs;
(3)Train technical personnel for clients .
2.Services during the sale:
(1)Pre-check and accept products ahead of delivery .
(2)Help clients to draft solving plans .
3.After-sale services:
Provide considerate services to minimize clients' worries.
(1)Complete After-sales service,professional engineers available to
service machinery at home or oversea.
(2)24 hours technical support by e-mail.
(3)Other essential technical services.
Quality warranty:
Our products are made of high quality steel and all spares parts
are inspected strictly before shipping. We have quickly responses
for your complaint and suggestion.
Package:
Using ply-wooden cases and pallet for package to protect the
products and avoid the damagement during transportation. Also we
can customize package according to your special requests.
Production time:
Generally need 15-25 days
Transportation:
By air, By Express or By sea according to your requests.
