Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
NC servo yaw is a test case for roller feeder adjustment
1. Start the correcting machine or material holder and slowly release the material.
2. Adjust the position of the two stopper wheels according to the
width of the material, so as not to hinder the operation of the
material.
3. Will relax the cylinder on the platform, put the material
between the upper and lower rollers, put down the cylinder to press
the material, adjust the air source pressure gauge to avoid the
material is not tight and slip, resulting in inaccurate feeding.
When the thickness of the material changes, it must be readjusted.
.
4. After setting the feeding length, look at the actual situation,
and set the feeding speed accordingly. The method of setting is
described in detail in the previous section.
5. After the relevant parameters of the feeding are set, the actual
feeding length is not the same as the set value due to the number
of the divisor. Therefore, in the manual mode, press the feeding
test, punching, stroke, stamping, and adjusting the feeding. Actual
length
6. The adjustment of the feed start is adjusted by the rotary cam
of the press. The so-called feed start signal is to start at the
angle of the punch crankshaft.
NC servo yaw is a note for the roller feeder
1. The electrical equipment works under normal voltage. If the
voltage is constantly changing, the life of the electrical
components will be seriously shortened and the failure rate will
increase sharply.
2. This machine must not be overloaded. The operator at the
production site must operate in accordance with the instructions in
this instruction manual. In particular, it is necessary to master
the essentials and safety when loading, and must be supervised by
the person in charge.
3. The linear guide of the yaw unit and the ball screw are
precision components, and it is strictly forbidden to hit the
collision. Also check for loose screws and lubricated oil before
work every day.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
