Active Member
|
[China]
Address: No. 12, Chuangxing Road, Baisha, Humen Town, Dongguan, Guangdong, China
Contact name:Calin Deng
GUANGDONG RUIHUI INTELLIGENT TECHNOLOGY CO., LTD. |
|
|
Gear feeder, Dongguan Ruihui high quality uncoiling machine for coil
The installation of the gear feeder is divided into five major steps:
1. According to the requirements of the stamping process, determine the feeding direction and installation position of the gear feeder.
2. Determine the position of the center line on the side of the punching table of the punch feeder.
3. Align the center line of the mounting bottom plate of the gear feeder with the center line of the side of the punching table, drill the tapping on the punching machine body, and fix the feeder mounting plate on the punching bed. Pay special attention to the feeder. The centerline of the mounting plate matches the centerline of the punching table.
4. Fix the fuselage body of the gear feeder on the mounting plate, in which the fixing screws should not be tightened temporarily, and then adjust the height adjustment screw on the mounting plate according to the height of the center line of the mold, so that the discharge center line of the feeder and the mold feed The center line ensures the upper and lower and left and right absolute levels, and then the fixing screws between the mounting base and the main body of the feeder and the lock nut on the height adjusting screw are respectively locked.
The method of checking the level: start the punching machine, use the inching method to move the punching slider to the dead point, and release the gear feeder to release the cam. The purpose is to relax and not work, feed the material into the feeder, and synchronize with the hand. The pulley is fed into the mold to observe whether the material is smooth and has no resistance in the mold. If there is resistance or jamming, it indicates that it is not level, and it can be adjusted by adjusting the mold or the feeder.
5. Connect the gear feeder to the fixed output shaft of the punching machine. (The stamping customer should provide the relevant size of the output shaft when ordering the gear feeder.) Adjust the length of the transmission belt to the appropriate by adjusting the tension pulley. The entire installation process of the Ruihui gear feeder.
Specification:
| Model | MAC2-400 | MAC2-500 | MAC2-600 | MAC2-800 | ||
| Stock Width(mm) | 50-400 | 50-500 | 50-600 | 50-800 | ||
| Stock Thickness(mm) | 0.3~3.2 | 0.3-3.2 | 0.3-3.2 | -3.2 | ||
| Max.Coil Weight(kg) | 3000 | 3000 | 3000 | 5000 | 5000 | 7000 |
| Max.Coil O.D.(mm) | 1200 | 1200 | 1200 | |||
| Coil I.D.(mm) | 8 | 8 | 508 | 508 | ||
| Feed Length(mm) | ~500* | ~500* | ~500* | ~500* | ||
| Max. Line Speed(m/min) | 16-24 | 16-24 | 16-24 | 16-24 | ||
| Work Roll Number(pieces) | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | upper 6 lower 5 | ||
| Feed Roll Number(set) | 1 | 1 | 1 | 1 | ||
| Main Motor(kw) | AC2.9 | AC2.9 | AC4.4 | AC4.4 | ||
| Mandrel Expansion | hydraulic | hydraulic | hydraulic | hydraulic | ||
| Reel Motor(kw) | 1.5 | 1.5 | 1.5 | 2.2 | 2.2 | 3.7 |
| Power(V) | 3 Phase 220V/380V/50HZ | |||||
| Operating Air(Mpa) | 0.49 | 0.49 | 0.49 | 0.49 | ||
Straigtening performance:
| tock Thicknees (mm) | Stock Width (mm) | |||
| 0.3 | 400 | 500 | 600 | 800 |
| 0.4 | ||||
| 0.6 | ||||
| 0.8 | ||||
| 1.0 | ||||
| 1.2 | ||||
| 1.4 | ||||
| 1.6 | 470 | 470 | ||
| 1.8 | 400 | 400 | ||
| 2.0 | 360 | 360 | ||
| 2.3 | 300 | 300 | 300 | 300 |
| 2.5 | 230 | 230 | 230 | 230 |
| 2.8 | 150 | 150 | 150 | 150 |
| 3.2 | 110 | 110 | 110 | 110 |
*1:(Pneumatic):Option in case of pneumatic mandrel expansion is
provi
