Edge Leader Corrugated Box Printing Machine With Slotter Knife 2000mm

Edge Leader Corrugated Box Printing Machine With Slotter Knife 2000mm
 
1.

Feeding Part
【1】 electric control machine from the alarm bell, continuous ringing warning, to ensure the safety of workers.
【2】 drive shaft with friction clutch, to avoid misuse and damage to the machine.
【3】 pneumatic interlock device.
【4】 The host motor starts the protection device. (The machine is not locked, the host can not start running)
2 . leading edge roller type feeding system
【1】 suction auxiliary feeding paper fan 7.5KW, according to the different bending conditions of cardboard, air volume adjustment,
To ensure smooth paper supply. Use the brush to remove the cardboard surface
Dust, scraps of paper and other debris, improve the printing quality.
[2] slotted with a chain control switch, control emergency stop paper.
【3】 The paper lift and down adopt the air cylinder,the action quickly, effort.
[4] the use of Shandong "Komori" front edge roller feed system, simple operation, high precision. The amount of extension can be adjusted, raw
Strong adaptability. Speed transmission more stable, suitable for warping, thin cardboard transmission, the effect is obvious.
【5】 side baffle, rear box position by the screw electric adjustment; front baffle upper and lower gap position manually synchronized adjustment.
【6】 skip feeding device (according to the need to choose continued or sheet feeding).
3. Feed roller
【1】up roller use the soft rubber shaft ,so when feed the board ensure the not borken the board
【2】 The lower feed roller with embossing roller diameter ¢ 155 mm, seamless steel pipe, embossed hard chrome plating.
【3】 feeding roller cross slider-type dial dial manually adjust the adjustment range of 0 ~ 12 mm. Adjustment does not affect the gear gap, to ensure transmission accuracy.
【4】 hand-type quick clearance fine-tuning self-locking device.
2.Printing department
1 printing roll (plate roll)
【1】 diameter of ¢ 408 mm ( ¢ 408 mm with printing mould diameter).
[2] high-quality steel surface grinding, axial reference scale, hard chrome plating.
[3] to do the balance correction, smooth operation, to adapt to high-speed operation.
【4】 ratchet fixed scroll plate, with hanging plate ditch, to adapt to the rapid version of the installation convenient and quick.
【5】 full version of hanging slot, for 10 mm hanging version of the article.
【6】 printing roller axial manual traverse, the maximum movement of 10mm.
2 printing press roll
【1】 diameter of ¢ 155 mm.
[2] the use of high-quality seamless steel pipe surface grinding, dynamic balance correction, smooth operation, hard chrome plating
【3】 printing pressure roller cross slider-type dial to manually adjust the adjustment range of 0 to 12 mm. Adjustment does not affectGear clearance to ensure transmission accuracy.
3 Feed the upper and lower rollers
【1】 on the roll: diameter ¢ 86 mm seamless steel pipe, with three paper feed ring.
【2】 the next roll: diameter ¢ 155 mm seamless steel pipe, surface grinding, hard chrome plated
【3】 feeding roller cross slider-type dial dial manually adjust the adjustment range of 0 ~ 12 mm. Adjustment does not affect teethWheel clearance, to ensure transmission accuracy.
4. steel anilox roller rubber roller set ink system
[1] diameter of ¢ 176 mm. Dalian roller .
【2】steel surface grinding, repression reticulate, hard chrome plating.
[3] alance correction, smooth operation.
【4】mesh number is 180,200,220,250 lines / inch selection.Option ceramic roller 300line/inch
【5】 with the feed system pneumatic automatic lifting device. (When feed paper pr the anilox roller is lowered and touched with print plate ,stop feed paper
anilox roll is up and the plate is separated)
【6】 Anilox roller with wedge-type clutch, even ink, easy to clean ink.
【7】 rubber roller diameter ¢ 168 mm.
【8】 steel pipe surface wrapped with wear-resistant rubber, and do the balance correction.
【9】 rubber in the special high grinding, ink transfer effect is good. Quick clearance fine-tuning self-locking device to ensure uniform ink. The amount of uniform ink system, the conversion effect is good, to extend the life of rubber roller.
5 .phase adjustment mechanism
[1] planetary gear structure.
[2] print phase adopt electrical digital number adjust 360degree adjutable
6. ink circulation
【1】 Pneumatic diaphragm pump, ink stability, easy operation and maintenance.
【2】 ink filter, filter impurities.
7 printing phase fixing device
【1】 cylinder brake mechanism.
【2】 When the machine to separate or adjust the phase, the brake mechanism to limit the machine rotation, to maintain the original gear position fixed point.
3.die cutter with slotter knife attachment
Wooden die roller (lower roll)
【1】 outside diameter ¢ 250mm (without cutter).
[2] cast iron surface grinding, hard chrome plating, balance correction, increase operational stability.
【3】die fixed screw hole spacing, axial 100mm; radial 12 equal parts. Applicable tool height 25.4mm.
【4】Wood template thickness: 16mm (for three-layer paperboard) 13 mm (for five-layer paperboard)
Pad roller (upper roll)
【1】 diameter of ¢ 332mm, aniv cover 349mm
【2】 quick change type pad, wear resistance, long life.
[3] cast iron surface grinding, hard chrome plated.
[4] balance correction, increase operational stability.
【5】pad thickness of 9m. Width 250mm. Mechanical type transverse 40mm swimming device. (Adjustable swimming speed)
4. Auto stacker with vibrator - optional
Auto stacker part :
1.the paper taking arm is manual operation. The paper stacking height can be chosen freely.
2.Adjustment is available for each belt.
3.The paper feeding platform transmitted up and down by chain.
4.the inclination of paper taking platform is changing as the height of the paper. Brake is installed to fix the platform’s position.
5.when the paper stacking height reach the set point. the paper taking platform will hold the paperboard pneumatically.
6.Maximum stacking height:1600mm.
7.the transmission belt driving motor:2.2kw
8.platform goes up and down driving motor:2.2kw.
9.paper taking arm cylinder:80mm×300mm.
Auto vibrator part :
THE MACHINE FUNCTION :
This machine is match equipment with middle and high speed rotary die cutter machine,it structure easy ,operation convenient , waster paper clearance effect well , economic, during the course of the working ,reduced the worker force , that is ideal equipment of the carton industry.
This machine include the paper feed part , collect waste paper part ,and walk lock system
paper feed part : that is transmit roller with PU round belt made of the paper feeding , during the paper feeding, there have two vibration rod , let the board vibrate on the belt , so get the result of clear the waste paper .
Waste paper collect part : this part is the let the waste paper feed out belt ,then use other belt feed the paper to side of the machine , finished the collect waste and feed waste paper .
Walk locking part : there include four guide wheel ,let the machine depart and lock with the rotary die cutter , operate easy , lock part have pneumatic and lock cylinder ,let it with rotary die cutter fix .
The size of the machine we will according the rotary die cutter size make ,
If you have old rotary die cutter ,please tell me the your machine size .
5.Installation and commissioning
If need the installation ,buyer need pay the double way ticket , food ,hotel , 100usd /day
Note: Customer-owned prepare part
1, compressed air pipe, compressor.
2, power, wire connected to the operating cabinet and line pipeline.
3, water, water pipes.
4, water, electricity, gas foundation plane installation of civil works.
5, equipment with oil, lubricants, hydraulic oil, grease and high temperature grease.