CHINA YIKE GROUP CO.,LTD |
|
Fully Automatic 5 Layer Corrugated Cardboard Production Line / Paperboard Production Line
※Structural features:
★Symmetrical structure can also install two bundles of paper at the
same time,Paper can be used for non-stop for a job;Adopts
mechanical drive to complete the paper clamping, lifting, loosen,
move on, around translational motion, etc.
★each shaftless mill roll stand is equipped with two pieces of
paper guide, two set of paper car;paper guide the use of channel 14
and the guide post weld,paper car adopt 10mmwelded stell,the length
of track is 4500mm.
★manual dics brake,add screw following
★electric elements centralized control the electric elements,expand
chuck
※technical parameters:
1,Backstands action mode:mechanical electric operation
2,the range of paper jams:maximum:1800mm minimum:600mm
3,the diameter of paper jams:maximum:¢1400mm minimum:¢400mm
4,Unilateral maximum load:maximum2000Kg
5,Powered motor parameters:
①Paper jams motor550W×4set 380V 50HZ short(S2)working standard
②lift motor 1.5Kw 380V 50HZ short(S2)working standard
※Structural features:
★push the roller in place
★track whole buried, The main frame of the 14th channel with ¢ 20mm
cold drawn round welding,the track length 4500mm
★Each paper with two stage paper trolley,and the paper from the two
sides at the same time
※Structural features:
★In accordance with national standard category pressure vessel,and
with the pressure vessel certificate.
★The roll surface after precision grinding, fine grinding and hard
chromium plating processing,surface friction,durable.
★electric adjustable angle, angle can rotate in the range of
360°,and adjust the paper preheat area.
※technical parameters:
1,diameter of the preheat roller:¢600mm
Diameter of the angle:¢85mm×2
2,work power:380V 50Hz
3,motor power:250W short(S2)work system
※Structural features:
★Adopt vacuum suction structure, with high pressure strong
blower.Suction with silencer.Gas supply and electrical control
cabinet to focus on the same operation cabinet,not less than 1.5
meters away from the host,Fully enclosed full operation side.
★base and wallboard cast iron wall,Wallboard
thickness130mm.universal Joints.
★corrugated roller material adopt 48CrMoalloy steel,quenched,Laser
hardening,Surface finish,main roll of corrugated diameter¢
280mm,surface hardnessHRC60degree above.The key parts of the tile
and pressure roller bearings Wafangdian produce high temperature
bearings.
★pressure roller ¢ 284mm,surface grinding and
chrome-plated;cylinder control and remove up and down, 45 carbon
steel materials, quenching (with cushioning devices).
★pneumatic control glue to glue back, glue roller diameter
¢215mm,Engraved polished surface after a 36-line pit style textured
machined chrome plated,after scraping the roller surface polished
hard chrome plated.
★Corrugated roller, pressure roller materials provided by the
Central Plains Steel,High on corrugating unilateral 0.15mm, 0.075mm
high pressure roller unilateral. Plus stopper. ¢ 160mm cylinder
with compression cylinder.
★preheat roll adopt seamless steel pipe production by tiangang ¢
300mm,connecting with metal Hose
※regular technical parameters:
1,effective width:1800mm 2,operation direction:left or
right(determined in accordance with customer plant)
3,design speed:100m/min 4,temperature range:200—260℃
5,corrugated flute:(UV type or UVV type)
※roller diameters parameters:
1,diameter of corrugated roller: ¢280mm 2,diameter of pressure
roller: ¢284mm
3,diameter of glue roller: ¢216mm 4,diameter of preheat roller:
¢320mm
※powered motor parameters:
1,main drive motor:7.5Kw rated voltage:380V 50Hz Continuous (S1)
working standard
2,suction motor:7.5Kw rated voltage:380V 50Hz Continuous (S1)
working standard
※structural features:
★This part is the main beam of the 20th channel, 16-beam, angle
iron 63, column, etc. are connected.
★Both sides of the security fence, ladder , high-strength save
people the word pedals, ensure the safety of personnel and easy to
operate.
★Pull the paper shaft surface tension axis, feeding shaft by
grinding hard chrome plated.★Vacuum tension control, 5-inch suction
tube, plus regulating valves, air flow can be infinitely
adjustable.
★Dual front bezel correction guide column positioning, screw
driver, fast and accurate positioning, walking steadily.
※roller diameters parameters:
1,Paper roll and a tension roller diameter:¢130mm diameter of
conveyor roller:¢110mm
2,Active tension roller diameter:¢85mm diameter of over paper
rollers and guide rollers:¢110mm
3,Paper towing shaft diameter:¢110mm
※Motor and electrical parameters:
1,corrugated single paper lift motor:3Kw 380V 50Hz
continuous(S1)work system
2,The bridge adsorption motor:3Kw 380V 50Hz continuous(S1)work
system
3,Wide motor tune cardboard: 250W 380V 50Hz short(S2)work system
※Structural features:
★preheat roller accord with the national standard of the pressure
vessal,and enclosed the pressure container certificate and
inspection certificate.
★Each roller surface after grinding precision grinding and dealing
with hard chrome plating, Surface friction is small, durable.
★electric adjustable angle, it can rotated adjust the paper preheat
area in the range of 360°
※technical parameters:
1,diameter of preheat roller:¢600mm range of angle
adjustment:360°rotation diameter of wrap angle axis:¢85mm
2,steam temperature:150-200℃ steam pressure:0.8-1.3MPa
3,motor power:250W short(S2)working system 380V 50Hz
※Structural features:
★After the glue roller surface after quenching inner hole
machining, grinding and dynamic balancing surface engraved with pit
style textured, coating evenly, less consumption of plastic.
★doctor roller surface by grinding and hard chromium plating.
★other guide rollers with hard chrome plated.
★Pressure roller with pneumatic lift, easy operation.
★ manually adjust scraping gap.
★glue roller ¢ 215mm,Doctor roll¢ 122mm,press paper roller¢
122mm,preheat roller 270mm.
★Electrical design, construction production process, follow the
national standards, low failure rate, easy maintenance.
※regular technical parameters:
1,MAX.working width:1800mm 2,operation direction:left or
right(Determined in accordance with the customer's facility)
3,design speed:100m/min 4,Gas supply system:0.4—0.6Mpa
5,Preheat cylinder temperature range:150—200℃ Steam
pressure:0.8—1.2Mpa
※Roller diameter parameters:
1,glue roller diameter:¢215mm doctor roller diameter:¢122mm
2,lower preheating roll diameter:¢270mm under preheat roller
diameter:¢270mm
3, Over the paper roll diameter:¢85mm
※Power motors and electrical parameters:
1,glue roller initiative frequency motor:3KW 380V 50Hz Continuous
(S1) working standard
2,glue pump motor: 2.2KW 380V 50Hz Continuous (S1)working system
※Structural features:
★Heating plate surface by grinding treatment, hot plate width
600mm, a total of 12 heating plate and cooling 4 m.
Heating plate with a container board production, in line with
national standards for a class pressure vessel, with pressure
vessel certificate and inspection certificate.
★Hot plate with intensive gravitational roll structure. Roll adopt
pneumatic lifting.
★Heating plate heat transfer pipe temperature control
sub-four-segment, with a temperature display.
★on cotton use two-cylinder S type cotton belt with the tensioning
device.
★lower belt adopt pneumatic tensioning.
★Drive roller coated with attached wear-resistant rubber ,showed a
herringbone structure,With a high, ensure smooth cardboard output.
★Main drive motor for frequency conversion motor,low-speed
torque,wide speed range ,reliable, and easy maintenance.
★hot plate internal for partition isolation structure,s-shaped flow
of steam,Steam, water separation function significantly improves
the utilization of steam.
※ technical parameters:
1,temperature requirement:160—200℃ steam pressure:0.8-1.3MPa 2,air
source pressure:0.6—0.9MPa
3,Cooling stereotypes length:4m Heating plate quantity:12 pieces
4,hydraulic system pressure:6---8MPa
※roller diameter parameters:
1,upper drive rubber roller diameter:¢475mm lower drive rubber
roller diameter : ¢350mm Wear rubber Outsourcing
2,Former follower with roller diameter:¢215mm back setting belt
driven roller diameter:¢176mm
3,Platen roller: ¢70mm Setting roller diameter:¢86mm
4,upper belt tension roller diameter:¢155mm upper roll diameter
with detuning:¢124mm
5, Entrusted with the roll diameter lower belt:¢130mm
Note: All the roller surface after grinding are hard chrome plated.
※Power motors and electrical parameters:
1,Main drive motor power:22Kw 380V 50Hz Continuous (S1) working
standard
※structural feature:
★Overcome the conventional type of pole, cutting pressure lines
appear when collapsed cardboard cut phenomenon, cutting board
smooth, quality has improved significantly.
★the whole machine can remove left and right,cycloid reducer to
adjust.
★Cutter and easy to adjust the pressure line, the error ± 0.5mm,
automatic sharpening device, you can achieve timing Brothers, with
intermittent Brothers and other features.
★the machine adopt five knives eight lines,the blade is made of
tungsten alloy steel, the using life is not less than 3 million
running meters.
※regular technical parameters:
1,effective width:1800mm 2,The maximum mechanical speed:100m/min
3,Mechanical configuration: 5knives 8lines 4,The minimum width of
the cutter:135mm
The maximum width of the cutter:1850mm
※Power motors and electrical parameters:
1,Line cutter line motor:0.4Kw 2,Knife wheel drive motor:5.5Kw
※structural feature:
★it can store 200 units orders,replace the cutter specifications
quickly and accurately,changing orders without stop,And enables
networked computers to facilitate production management.
★Knife shaft drive gears are precision forged steel induction
hardening, backlash-free transmission, advanced keyless connection,
high transmission accuracy.
★Cutting machine adopts inlaid front steel blade knife spiral
structure, serrated knife. scissors, shears, shear force, long
blade life.
★around feed rollers are used the sun gear platen way, smooth
delivery, pressure evenly, easy to crush plate board or cause
blockage.
★Exact and adjustable no gap gear to ensure precise blade
engagement, running balance.
★Knife roller: fine quality forged steel material, the balanced,
with good stability.
★Germany Bryant servo motor drive controller, Taiwan Eview yield
10.4 inches color touch screen display, the project at a glance.
★Cutting length: 500mm-9000mm, cutting precision: ± 1mm (at steady
speed).
※regular technical parameters:
1,Minimum cutting length:500mm 2,Maximum cutting length:9999mm
3,Cutter accuracy: Uniform for ± 1mm, non-uniform to ± 2mm
※Roller diameter parameters:
1,Cross on the knife shaft center distance:¢216mm 2,Before the
lower conveying roller diameter ¢156mm
3,After the lower conveying roller diameter: ¢156mm 4,The front of
the platen roller diameter: ¢70mm
5,The front of the platen roller diameter: ¢70mm
Note: After all have been grinding rollers, hard chrome plated at
(on except under the knife shaft) dealing.
※Power motors and electrical parameters:
1,main drive motor power:12.5Kw Full AC synchronous servo
2,Before feeding motor power:3Kw(Frequency Control)
3,Oil pump motor power:0.25Kw
※DMT-120 paper sheet delivery and side conveyor
※structural features:
★Adopted on the 16th channel welded.Electric adjustment of
cardboard the size of the lateral output pneumatic control board,
electrically adjustable conveyor speed.
★Cardboard sheets to the desired number or height requirements will
be controlled by a foot switch out of cardboard.
★Vertical bin using wide flat belt conveyor transport.
※technical parameters:
1.The maximum accumulation length:3000mm
2,The maximum stack height:200mm
※Power motors and electrical parameters:
1.Main conveyor motor:3Kw adopt frequency motor
2,Lateral output of the motor:1.5Kw Three-phase asynchronous motor
3,Walking Motor:1.5Kw Three-phase asynchronous motor