Anti Wrinkle Installation Tube Pipe Bending Machine For Madical Bed
-- Mechanical features
1. High performance middle size pipe bending
machine, with NC control, multi-groups program and multi angles
setting, it makes your operation and setting convenient.
2. Widely used in mass production and standard
products, such as blast pipe, seat, fender guard and all the steel
3. The machine is NC control and hydraulic
drive, it can have different bending degrees to prefabricate.
4. PLC control and the machine runs steadily.
5. It has various functions can be chosen, such
as manual operation, automatic, semi-circulation, full-circulation
6. Two angle setting, 0° to 185° is chosen at
will. It can choose an angle or two angles continuously.
7. Mobile type foot switch with three functions,
auto start, emergency stop, going on after emergency stop.
8. The safety is high.
9. Large volume cooling circulation system to
make the machine run more steadily.
10. Model exchanging is simple and convenient to
be in flexible manufacturing.
11. The designing of the machine head and pipe
bending precision is high and the bending space is large.
-- Installation points
1. Bending die installation
Plunge the elbow in a clockwise direction and
cap it. Replace the required elbow wheel die and tighten the cap.
2. Clamp mold installation
Insert the clamping die with adjusting bolts,
adjusting plates and cover plates into the clamping die holder and
connect the adjusting bolts. The clamping die of the adjusting
plate, cover plate, etc. is inserted into the clamping die holder
and the adjusting plate is inserted. Fix on the clamp mold base and
rotate the adjusting bolt so that the center of the clamp mold and
the center of the bend tube mold are on the same plane. Then adjust
it as follows:
2.1. Loosen the clamping bolts and press the
manual “Pinch” button until the clamped mold reaches the end point
(there is a gap between the bending tube mold and the clamping
2.2. Adjust the clamping mold seat adjustment
screw so that the clamping mold and the bending tube mold are fully
2.3. Press the “Retreat” button to retract the
clamping mold, and then turn the clamping mold adjustment screw
into about 1/4-1/2 turns.
2.4. Lock the clamping block fixing bolt.
3. Skateboard die adjustment method ditto
4. Mandrel and cylinder installation
4.1. Screw the mandrel onto the mandrel screw
and fix the mandrel to the proper position to fix the nut.
4.2. Relax the mandrel cylinder bolts.
4.3. The pointer of the moving mandrel cylinder
block is related to the scale of the rail holder and the radius of
4.4. Lock the mandrel and cylinder.
5. Anti-crease device
The wrinkle-resistance mold is mounted on the wrinkle-proof plate
seat, and it can be properly adjusted as shown in the figure by 1°
6. Bending angle adjustment
The bend angle control is controlled by a
proximity switch, a scale display is shown at the adjustment
position of the proximity switch, and the proximity switch
adjustment block is adjusted to a desired angle.
Above is the first angle, below is the second angle, corresponding
to the angle/double angle selection on the operation panel, after
the trial bend and then trim the angle. Because the material of the
pipe is different, the rebound amount is also different. After the
adjustment is completed, the locking screw lock nut on the nut will
7. Overflow valve pressure adjustment
Press any of the manual buttons of pinch tube,
back clamp, core, and back core to release the pressure displayed
on the pressure gauge. At this time, rotate the pressure relief
handle of the overflow valve to adjust the pressure to the desired
pressure of 10 MPA. The bending resistance should not be too high,
so as not to increase the oil temperature and to accelerate the
wear of hydraulic components.
-- Main application
Adapted material: steel pipe, stainless steel,
copper pipe, aluminum pipe;
House structure, shipyards, automobile
production, industrial pipeline equipment, pulp, paper, chemicals,
boilers, pump stations, site fresh water and wastewater systems,
municipal heating and cooling systems, urban gas pipelines,
municipal works such as hospitals, office buildings, construction
and large-scale public buildings, medium and large-scale industries
for maintenance and repair work, power stations, installation
companies, automatic fire sprinkler systems in front of workshops.
-- Specifications of machine
|Maximum applicable carbon steel pipe||Φ75*3.0t|
|Maximum applicable stainless steel pipe||Φ63*3.0t|
|Maximum applicable copper pipe||Φ89*3.0t|
|Maximum coring length||2800mm|
|Maximum bending radius||300mm|
|Maximum bending angle||190°|
|Settable bending pipe number of each pipe fitting||15|
|Maximum oil pressure||14MPa|
-- Packaging and service
1. Payment terms: 30% T/T down payment and 70%
T/T before shipment.
2. Delivery time: No later than 15 days since
receiving the advance payment.
3. Validity of the price: For ONE month.
4. Package: Wooden case.
5. Warranty period: We guarantee machine quality
for 12 months. During this period, if spare parts of the machine
were damaged, we can send the component to the customer by
international express service freely.
-- Pictures of machine