Active Member
|
[China]
Address: Building 12, Songshan Lake, Small and Medium-Sized Science and Technology Park, Dongguan City, 523808, Guangdong Province, P.R.China
Contact name:KOMEG
KOMEG Technology Ind Co., Limited |
|
|
KOMEG Automatically Salt Spray Test Small Environmental Chamber
1. Application
Salt water spray test chamber is widely used in Corrosion
resistance test for products after treated by plating, anodized,
spraying, and anti-rust, to test the surface treatment of various
materials. Those so-called treatments include coating,
electroplating, and films of organic and non-organic materials,
anodizing, anti-rest oil and corrosion resistant treatment, which
may achieve the purpose of keeping the items from being
corroded for a longer period.
2. Features you need to know, If you are new to Salt Spray Tester:
1) The whole part of the device is made of P.V.C. Sheet and
the inside of the device is reinforced by using a special lining
material. Hence, it is sturdily made and will not transform
forever.
2) The test chamber is heated from five directions in order
to ensure the temperature difference in the chamber may be kept
within (± 1℃).
3) Spray nozzle: The nozzle is specially made to enable it to
suck up the salt water and then spray it out in the shape of mist
with considerable high speed. When it falls on the surface of the
item being tested, the difference of fallen mist may be controlled
within ± 0.3ml / 80 cm2h.
4) HUNTER PRINCIPLE is used to make the saturated air hot and
moist and to keep the humidity in the test chamber required for
test.
5) Temperature is the pre-requisite condition that with have
direct impact on corrosion rate. We use P.I.D. temperature control
unit to limit the temperature difference within the range of ±
0.5℃.
6) A warning device is used to indicate the low level of the
test fluid, when the fluid is only enough for being sprayed for
five hours, a buzzer will remind the user to replenish the liquid
to ensure continuous spray test.
7) Use full automatic detecting system, test stopped
automatic, and lighting display when trouble.
3. Main Technical Parameter:
| Specifications (Note: We reserve the right to change specifications without prior notice) | ||||
| Model | HL-160-NS | HL-120-BS | HL-90-BS | HL-60-SS |
| Interior dimensions(W*H*D)mm | 1600 X 500 X 1000 | 1200 X 500 X 800 | 900 X 500 X 600 | 600 X 400 X 450 |
| Exterior dimensions(W*H*D)mm | 2240 X 1500 X 1600 | 1410 X 1280 X 880 | 1460 X 1280 X 910 | 1130 X 1070 X 630 |
| Testspace Volume(L) | 800 | 480 | 270 | 108 |
| Salt Water Tank Volume (L) | 60 | 40 | 25 | 15 |
| Heater | 15KW+1KW | 11KW+1KW | 7KW+0.75KW | 3KW+0.75KW |
| Air compressor | 2HP | 2HP | 1/2HP | 1/2HP |
| Temp. range (Testing barrel) | 35±1℃～50±1℃ | |||
| Temp. range (Pressure barrel) | 47±1℃～63±1℃ | |||
| Test applicable | NSS, ACSS,CASS,CORK | |||
| Pressed Air Pressure | 1.00±0.01kgf/cm² | |||
| Spray Amount | 1.0~2.0ml/80cm²/h(Collect at least 16 hours, take the average) | |||
| Ambient Relative Humidity | More than 85%R.H. | |||
| PH Value | 6.5~7.2 3.0~3.2 | |||
| Spraying Manner | Programmable Spraying | |||
| Power | AC220V 1Φ 50Hz | |||
4. Know the following Typical coatings that can be evaluated with
this method are:
1) Phosphated surfaces (with subsequent paint/primer/lacquer/rust preventive)
2) Zinc and zinc-alloy plating (see also electroplating). See ISO 4042 for guidance
3) Electroplated chromium, nickel, copper, tin
4) Coatings not applied electrolytically, such as zinc flake coatings according to ISO 10683
5) Organic coatings
6) Paint Coating
5. About the Corrossion Tolerance Testing Machine
A: the front side
1. Dry-bulb thermometer
2. Wet-bulb thermometer
3. Hopper
4. Hopper protecting cover
5. Laboratory cover
6. The water inlet of salt water supplement
7. Operating panel
8. Saturated barrel water inlet
9. Pressure regulating valve
B: the back side
1. Exhaust port
2. The drain port
3. The drain valve
4. Air inlet
5. Power line 220v single
6. Package Info
|
