Structure of FPC
According to the number of layers of conductive copper foil, FPC
can be divided into single layer circuit, double layer circuit,
multi-layer circuit, double sided and so on.
Single-layer structure: the flexible circuit of this structure is
the simplest structure of the flexible PCB. Usually the base
material (dielectric substrates) + transparent rubber(adhesive) +
copper foil is a set of purchased raw materials(semi-manufactures),
the protective film and transparent glue are another kind of bought
raw material. First, copper foil must be etched to obtain the
required circuit, and the protective film should be drilled to
reveal the corresponding pad. After cleaning, the two are combined
by rolling. Then the exposed part of the pad electroplated gold or
tin to protect. In this way, the big panel board will be ready.
Generally also it’s stamped into the corresponding shape of the
small circuit board. There is also no protective film directly on
the copper foil, but printed resistance soldering coating, so that
the cost will be lower, but the mechanical strength of the circuit
board will become worse. Unless the strength requirement is not
high and the price needs to be as low as possible, it is best to
apply the protective film method.
Double layer structure: when the circuit is too complex to be
wired, or copper foil is needed to shield the ground, it is
necessary to choose a double layer or even a multilayer. The most
typical difference between a multilayer and a single plate is the
addition of a perforated structure to connect the layers of copper
foil. The first process of transparent rubber + base material +
copper foil is to make holes. Drill holes in the base material and
copper foil first, clean and then plated with a certain thickness
of copper. The subsequent fabrication process is almost the same as
the single-layer circuit.
Double sided structure: both sides of the double sided FPC have
pads, mainly used to connect other circuit boards. Although it and
monolayer structure is similar, but the manufacturing process is
very different. Its raw material is copper foil, protective film
and transparent glue. The protective film should be drilled
according to the position of the pad first, then the copper foil
should be affixed, the pad and track lines should be etched and
then the protective film of another drilled hole should be affixed.
Copper foil is available in two different types of copper: ED
Copper and RA copper.
ED copper is an electro-deposited (ED) copper foil produced in the
same way as the copper foil used for rigid printed circuit boards.
This also means that the copper is “treated”, i.e., it has a
slightly rough surface on one side, which ensures a better adhesion
when the copper foil is bonded to the base material.
RA copper is a rolled and annealed copper foil produced from
electrolytically deposited cathode copper, which is melted and cast
into ingots. The ingots are first hot-rolled to a certain size and
milled on all surfaces. The copper is then cold-rolled and
annealed, until the desired thickness is obtained.
Copper foil is available in thickness of 12, 18, 35 and 70 μm.
The most common available for dielectric substrate and coverlay is
polyimide films. This material can also be used as coverlay.
Polyimide is best suited for flexible circuits because of its
characteristics as stated below:
High temperature resistance allows soldering operations without
damaging the flexible circuits
Very good electrical properties
Good chemical resistance
Polyimide is available in thicknesses of 12.5, 20, 25 and 50 μm.
Base laminates for rigid printed circuit boards are copper foils
laminated together with the base materials, the adhesive coming
from the prepreg material during lamination. Contrary to this is
the flexible circuit where the lamination of the copper foil to the
film material is achieved by means of an adhesive system. It is
necessary to distinguish between two main systems of adhesive,
namely thermoplastic and thermoset adhesives. The choice is
dictated partly by the processing, and partly by the application of
the finished flexible circuit.
FPC Case: Flexible PCBs | Thin PCBs | Polyimide PCBs | Single Sided
FPC
(FPC’s are custom-made products, the picture and parameters shown
are just for reference)
General description
This is a type of single layer flexible printed circuit for the
application of Wireless Dongle, 0.2mm thick. The base laminate is
from ITEQ, It’s fabricated per IPC 6012 Class 2 using supplied
Gerber data. Polyimide stiffener is applied on the inserting head.
Parameter and data sheet
| Size of Flexible PCB | 230.5 X 40.8mm |
| Number of Layers | 1 |
| Board Type | Flexible PCB |
| Board Thickness | 0.20mm |
| Board Material | Polyimide (PI) 25µm |
| Board Material Supplier | ITEQ |
| Tg Value of Board Material | 60℃ |
| |
| PTH Cu thickness | ≥20 µm |
| Inner Iayer Cu thicknes | N/A |
| Surface Cu thickness | 35µm (1oz) |
| |
| Coverlay Colour | Yellow |
| Number of Coverlay | 1 |
| Thickness of Coverlay | 25 µm |
| Stiffener Material | Polyimide |
| Stiffener Thickness | 0.2mm |
| |
| Type of Silkscreen Ink | IJR-4000 MW300 |
| Supplier of Silkscreen | TAIYO |
| Color of Silkscreen | White |
| Number of Silkscreen | 1 |
| |
| Peeling test of Coverlay | No peelable |
| Legend Adhesion | 3M 90℃ No peeling after Min. 3 times test |
| |
| Surface Finish | Immersion Gold |
| Thickness of Nickle/Gold | Au: 0.03µm(Min.); Ni 2-4µm |
| RoHS Required | Yes |
| Famability | 94-V0 |
| |
| Thermal Shock Test | Pass, -25℃±125℃, 1000 cycles. |
| Thermal Stress | Pass, 300±5℃,10 seconds, 3 cycles. No delamination, no blistering. |
| Function | 100% Pass electrical test |
| Workmanship | Compliance with IPC-A-600H & IPC-6013C Class 2 |
Features and benefits
Excellent flexibility
Reducing the volume
Weight reduction
Consistency of assembly
Increased reliability
Controllability of electrical parameter design
The end can be whole soldered
Material optionality
Low cost
Continuity of processing
Focus on low to medium volume production
More than 15 years of experience
Application
Mobile phone built-in antenna FPC, flex keyboard for mobile phone
keys, Industrial control computer soft board
Why choose us?
1) Focus on your core competencies: We’ve deeply known it is full
of fierce competition for our customers in the market. You can
focus on such important competencies as research and development,
sales and marketing based on our professional performance and
skilled services that exceeding your expectation.
2) Cutting-edge technology: it is rational for a small and
medium-sized customer to hanker after the latest equipment and
manufacturing expertise for its PCBs. By the partnerships
with Bicheng PCB, you gain access to reach your expectation with
our 3 factory bases with over 26,000 square meters.
4) Save the cost of production: Production cost is one of the key
points of our customers’ product competitiveness. Bicheng PCB have
been striving to reduce its manufacturing cost from equipment
introduce, worker training and technology improvement to increase
their profitability. Customers are satisfied with our cost savings
but without quality loss.
5) Avoid hassle: It’s an upset matter when quality problem hassling
you. Bicheng engineering design prevents problem from occurring in
pre-production. You will not get headache with Bicheng prototypes,
small orders and volume production. Our rate of customer complaint
is less than 1% and will be solved satisfactory.
6) Save time: Market requires the products updating quickly.
Bicheng PCB always works fast and flexible to save the time of
production from prototype to standard production,
quick turn-around or scheduled deliveries.
7) An excellent team: Bicheng is trustworthy partner with passion,
discipline, responsibility and honesty. We have a team of
experienced sales persons and skilled customer services. Do not
change your supplier. If change is must, Bicheng is the right one
for you.
