Active Member
|
[China]
Address: Changsha . Hunan China
Contact name:Laura
CHANGSHA PERFLEX NOVEL MATERIALS CO.,LTD |
|
|
EPOXY CERAMIC TILE GROUT, NON TOXIC HEALTHY EPOXY, READY TO GO, EPOXY MORTAR REPLACEMENT, DIY
P-20 TDS Epoxy Grout.pdf | Stain Resistance | Anti-Mould | Waterproof
Traditional white cement grout, need to be mixed before using and need professional worker to do it, usually people easy to have some problems about the mixing ratio, we need to cost much money to have work to do it for us, and it will become dirty and yellowing once it meets with water, you need to maintain it several months later, that is cost wasting and time-consuming. What's more, the bacteria breeding is bad for healthy. Nowadays epoxy cementitious mortar tile grout is very popular in the market, however it's also mess and complicated construct procedure, it's labor-costing and time-costing.
Perflex cartridge epoxy tile grout P-20 is two component, fixed mixing ratio, ready to go epoxy formulastion. No need to mix by worker, the special nozzle ensure totally mixed of the epoxy resin and hardener, it's easy to operate, everyone can do it, no need to cost money for finding workers, you can DIY for your house, also the durable service life will last for over 30 years.
FEATURE
APPLICATION
Perflex Epoxy Grout P-20 is suitable for bonding, filling and beautifying the joint of ceramic or stone building materials such as ceramic tile floor, ceramic tile wall, washbasin, bathtub, toilet, kitchen table, door-crossing stone, etc.
MECHANICAL PROPERTY
| Testing Item | Resin A | Hardener B |
| Appearance | Semi-fluid liquid | Thixotropic paste |
| Blend Ratio(by volume) | A : B = 1 : 1 | |
| Odor Grade | 3 | |
| Working time(25℃*min) | 30 min | |
| Original Curing | 25℃*4h | |
| Hardness(Shore D)≥ | 75 | |
| Colloidal fluidity after blending | Thixotropic fluid | |
| Bonding Strength | ≥5.5 | |
| Wear Resistance (750 g.500 r)/g | 0.050 | |
| Sagging after blending? | No sagging | |
| Tensile Shear Strength/MPa | Standard condition | ≥5.0 |
| High/low temperature switch. | ≥3.0 | |
| Water absorbent 25℃24 hour(%) | ＜0.2 | |
| Waterproof / 24h | No change | |
| Chemical Resistance / 2h | No change | |
| Stain Resistance (Vinegar, soy, oil)/ 1h | No change | |
| Testing condition: 21-25℃,relative humidity 45-55%. Constructed by caulking gun. | ||
CONSTRUCTION METHOD
1. After the mortar solidified, the ceramic tile crevice must be cleaned, the impurities and dust in the ceramic tile crevice must be cleaned up with wallpaper knife and vacuum cleaner.
2. Use cleaning wax on both sides of the gap beforehand with proper amount, pay attention not to wipe wax into the gap.
3. Twist the tube cap, install it on the head of the double-tube sealant, cut the spiral rubber nozzle obliquely at the head by 45 degrees (the opening size depends on the size of the tile seam), and then install it in the rubber gun.
4. Extrude about 20 cm colloid (in order to mix it fully and remove bubbles), then inject the glue into the crevice of ceramic tile.
5. Press the ready glue on the crevice with with the seam press or steel ball.
6. After 4-24 hours (depending on the temperature), the glue cures completely, scrape off the excess glue on both sides of the gap with a scraper.
PACKAGE
400ml per plastic cartridge, 20 Cartridge per carton.
SHELF LIFE
24 months if the product is stored in a dry and cool place away from light.
CAUTIOUS
1. The Storage of sealant should not be less than 5℃.
2. Construction temperature is suitable in the range of 15-30℃, too low temperature will affect the curing time and strength.
3. Impurities, dust, grease, clear water and other substances shall not be allowed during construction.
4. Do not touch or trample until the sealant is completely cured.
5. After use, the remaining glue can be put on the cover and can continue to use.
