VIIPLUS INTERNATIONAL |
|
The rolled bronze yellow POM (Polyoxymethylene) flanged sleeve bushing is a high-performance component designed specifically for boundary-lubricating applications. This unique combination of materials offers several benefits that make it ideal for demanding applications requiring superior wear resistance and lubrication properties.
Bronze, known for its excellent corrosion resistance and durability, is rolled into a sleeve shape to provide a strong yet flexible foundation for the bushing. The yellow POM material, a thermoplastic with exceptional mechanical strength and stiffness, is then fused or bonded to the bronze sleeve. The POM layer provides excellent wear resistance and low friction properties, which are crucial for boundary-lubricating applications.
The flanged design of the sleeve bushing allows for easy installation and secure positioning within the application. The flanges ensure that the bushing remains securely in place, reducing the risk of movement or misalignment during operation.
Boundary-lubricating applications refer to situations where the lubricating fluid or grease is present at the interface between the moving parts but is not fully immersed in a lubricant bath. In these scenarios, the lubricating film is thinner and more prone to disruption, requiring materials with superior wear resistance and lubrication properties. The rolled bronze yellow POM flanged sleeve bushing meets these demands by providing a durable and reliable solution for boundary-lubricating applications.
Overall, the rolled bronze yellow POM flanged sleeve bushing offers superior performance in boundary-lubricating applications, providing excellent wear resistance, low friction, and corrosion protection. Its design and material combination ensure reliable operation and extended service life in demanding environments.
Suitable for grease or oil lubrication and all kinds of movement, good load capacity, robust and insensible to dirt.
VIIPLUS of rolled (wrapped) bushings is produced with diamond shaped lubrication indents on the bearing surface(s). These bushings are ideally suited for thin wall applications. The indents provide lubricant reservoirs that allow for excellent and prolonged service.
For applications that are sealed or difficult to maintain, we also manufacture this product with self-lubricating graphite filled diamond or circular indents.
They are light-weight and compact and are available as sleeve bushings, flange bearings, washers and plates. They are produced in both inch and metric sizes.
VSB-20 Boundary lubrication bearing High Quality
POM Bush Chinese supplier
· marginally lubricated bushings for grease or oil lubricated
applications
· Standard parts contain grease indents in the sliding layer; plain
sliding layer available by request
· Optimum performance under relatively high loads and low speeds
· Suitable for linear, oscillating and rotating movements
· Wide range of parts available from stock
Suitable for rotating and oscillating movement, less maintenance
requirements due to the long re-lubrication intervals, lower wear,
lower susceptibility to edge loading, no absorption of water and
therefore no swelling, good damping behaviours, good resistance to
shock loads.
1. POM thickness 0.30~0.50 mm. It provides high wearresistance and low friction even with only
minute volume oflubricant are supplied, this bearing surface carries a pattern of circular indents which
should be filled with grease on assembly of the bearing.
2. Sintered bronze powder thickness 0.20-0.35mm. A special
composition of powdered copper is thermally fused to the steel
backing. This contact layer acts as an anchor for the PTFE layer
and conducts the thermal build up away from the bearing surfaces.
3. Low-carbon steel.Setting the foundation of the bushings, the steel back provides exceptional stability,load carrying and
heat dissipation characteristics.
· Metal-Polymer Composite Bushing Material
· Steel Back + Porous Bronze Sinter +
POM with Lubrication Indents
![]() | Sliding layer POM |
OPERATING PERFORMANCE | |
Dry | Poor |
Oil lubricated | Good |
Grease lubricated | Very Good |
Water lubricated | Poor |
Process fluid lubricated | Poor |
GENERAL |
| Unit | Value |
---|---|---|---|
Maximum load, p | Static | N/mm2 | 250 |
Operating temperature | Min | °C | - 40 |
GREASE LUBRICATED | |||
Maximum sliding speed, U | m/s | >2.0 | |
Coefficient of friction | 0.05 – 0.20 |
Max. load | Static | 250N/mm2 |
Dynamic | 140N/mm2 | |
Rotaing oscillating | 60N/mm2 | |
Max. speed | Dry | 2m/s |
Lubrication | >2m/s | |
Max. PV (Dry) | Short-time | 3.6N/mm2*·m/s |
Continuous | 1.8N/mm2*·m/s | |
Temp. | -195℃~+280℃ | |
Friction coefficient Dry | 0.03~0.20 | |
Lubrication | >2m/s | |
Thermal conductivity | 42W (m·k)-1 | |
Coefficient of thermal expansion | 11*10-6k-1 |
Bearing forms available in standard dimensions
· Cylindrical bushes
· Thrust washers
· Sliding plates
Metric bearings and imperial bushings made to order: standard
bushing forms in special dimensions, half-bushings, special shapes
obtained by stamping, bearings with locating notches, lubricant
holes and machined grooves, customized bushing designs
Recommended for applications involving intermittent operation or
boundary lubrication... Automotive: suspension joints, kingpin
assemblies and stub axles of trucks, automobile driving joint
hinges, steering and other linkages, articulation joints, rear
chassis hinges, fair leader rollers... Machine tool building
industry: spindles in drill, grinding, and milling machines, ram
guide plates in multi-ram presses... Agricultural equipment:
gearbox, clutch, bale trips and wheel caster swivels for bale
accumulators, front axle pivot bearings, steering idler box
bearings and kingpin bearings for harvesters... It is especially well-suited for applications where lubricant can
not be supplied continuously or repeatedly.
START YOUR
PROJECTWITH AN APPLICATION ENGINEER
Plain Bearings & Self-lubricating Bushings | VIIPLUS Surface
Engineering|Bearing Technology