Stainless Steel / Carbon Steel Insert Bearing NTN SSUC205-16 With 12 - 90 mm Bore Size

Stainless Steel / Carbon Steel Insert Bearing NTN SSUC205-16 With 12 - 90 mm Bore Size

Details

Packaging & Delivery

SSUC205-16 Stainless pillow  block bearing: 

The UC series insert bearing is fit to every kind of cast iron bearing housings, such as, P, PK, LP, PA, PG, PA2A, F, FU, FL, FLU, LF, FD, FC, T, ST, K 

You can buy insert ball bearing unit together or the insert ball and pillow block seperately.

TYPES OF BALL BEARING UNITS:

1.Pillow blocks

Pillow blocks are most extensively used among the bearing units, UCP, UCPK, UCAK and SBLPG, these type are fixed to the shafts by means of the setscrews prepared in the innering. While, NAP, NAPK and SALPG types are fixed to the shafts by use of setscrews prepared in the eccentric locking caollar. UKP type is mounted to the shafts by use of adapter sleeves.

2. High center height pillow blocks

UCPH2, NAPH2, UKPH2+H

It is one type of pillow blocks with a higher center height.

3. Tapped-base pillow blocks

UCPA, NAPA2, UKPA2+H

UCPA2A

UCPG2

It has compact structure, saving mounting space. It can be fitted with bolts from the underneath of the base.

4. Square flange units

UCF2, NAF2, NAFU2, UKF2+H, SAF2G

UCFX

UCF3,NAF3,UKF3+H

These bearing units are designed to fix at the sides of the machine which are vertical to the center of the shafts by means of 4bolts. The muonting method is widely used in the machines. The setsrews, the eccentric locking collar and the adapter sleeve bearings have the same mounting method as the P housings do.

5. Round flange cartridge units

UCFC2, NAFC2, UKFC2+H

These bearing units are installed in the holes on the side of the places where concentricity is demanded.

6. Oval flange units

UCFL2, NAFL2, NAFLU2, UKFL2+H, SBFL2G

UCFL3, NAFL3, UKFL3+H

This type of housing is useful in saving space and weight. It can be installed by means of two bolts. The set bolt pitch is the same as that of the square flange type.

7. LF, LFTC, FD, PFTD and PFTD-G type two-bolt flange units are for use with SB (or SB-G) and SA (or SA-G) type inserts only

SALF2G, SBLF2G, SALFTC2G, SBLFTC2G

SAFD2G, SBFD2G

SAPFTD2, SBPFTD2, or SAPFTD2G, SBPFTD2G

                                                                                    Bolt

                                           Material:                          Configuration:

LF, LFTC, FD                   Grey iron                         Round Hole

PFTD, PFTD-G                Ductile iron                     Square Hole

8. Flange bracket units

UCFB2

This type has three set holes on only one side of the flange. This type of bearing unit is used where the mounting space is limted, and the housing can be fixed on nly one side.

9. Adjustable flange units

UCFA2

This type has a two-bolt base with one side adjustable, enabling distance from center of shaft to be varied.

10. Take up units

UCT2, NAT2

UCK2

UCST2

This type is applied to the machines in which the center of main shaft needs free alignment.

11. Pressed housing pillow blocks

SAPP2, SBPP2

Pressed housings are with light weight and simple structure and consists of two pieces of pressed steel plantes. This type is applied to the machine whose rotating speed is lower or medium, or the machine with light load. The inserts for the pressed housings are usually SA or SB series.

12. Pressed housing round flange units

SAPF2, SBPF2

This type consists of two pieces of pressed steel plates, mounted with SA2 or SB2. It has light weight and simple structurem which is applied to the machine of which the rotating speed is low or mediem, of the machine load is light.

13. Pressed housing flange units

SAPGT2, SBPFT2

This type has the same function as the pressed round flange housing, It can be used where the mounting space is limited, because it takes smaller space.

14. Pressed housing oval flange units

SAPFL2, SBPFL2

This type has only two bolt holes. It needs much smaller mounting space. Its function is the same as the above-mentioned pressed flange husings.

15.Disk harrow units

Two pieces of pressed steel plates are riveted to form the housing fitted with "o" form rubber seals. It has four mounting bolt holes with tripple-lip seals inside. It can be relubricated through the grease nipple.