Active Member
|
[China]
Address: Room D-011 No. 517 Ming-ze Peninsula Luoshi South Road, Hongshan District, Wuhan City
Contact name:Cassie Xiong
Wu Han Micro Control Electric Co., Ltd. |
|
|
Multi - Function Tension Control System With Over-current Protection 180*110*70MM Tension Controller
Tension Control System Manual Tension Controller Output Voltage 36V Max Current 5A
ST-200M Manual tension controller (36V)
Features:
1. With Over-current, overheating short-cut protection.
2. No fan cooling
3. With panel,external connect PLC,external potentiometer control methods.
Attention:ST-203M installing size same as ST-200P
| Parameter | ||
| Model | ST-203M | ST-205M |
| Power supply | AC 180~260V 50/60HZ | |
| Output voltage | DC36V | |
| Output current | 0~3A | 0~5A |
| Dimension | ST-203M:180*110*137mm | ST-205M:246*154*114mm |
We also have other model for Option
ST-200 Multi-funtion manual tension controller
Features:
1. Adapt PFM and PWM technology,auto Over-current protection function.
2. With panel,external connect PLC,external potentiometer control methods.
3. With constant current,constant voltage,constant power(torque) three working modes.
| Parameter | |
| Model | ST-200 |
| Power supply | AC 180~260V 50/60HZ |
| Output voltage | DC24V |
| Output current | 0~4A |
| Dimension | 180*110*70MM |
ST-200W Manual tension controller
Features:
1. With Over-current, overheating short-cut protection.
2. No fan cooling
3. With forbidden output and allow output function.
| Parameter | |||
| Model | ST-201W | ST-202W | ST-203W |
| Power supply | AC 180~260V 50/60HZ | ||
| Output voltage | DC24V | ||
| Output current | 0~1A | 0~2A | 0~3A |
| Dimension | 96*96*129mm | ||
Normally manual tension controller can connect Magnetic powder brake or clutch in using.
General introduction:
The magnetic powder clutch is composed of active rotor (input
shaft),driven rotor(output shaft) and yoke with excitation coil.
The three parts are assembled relative concentric and form a system
which can rotate relatively. The annular gap between active rotor
and driven rotor is full of magnetic alloy powder which has high
magnetic conductivity.
The magnetic powder will be in the state of loose situation when
the current do not pass the excitation coil, the magnetic powder
will be thrown on the inner wall of active rotor, in this case,
there will not exist the interaction force between the active and
driven rotor. So the magnetic powder clutch is in the state of
separation, no torque transmission exits.
The magnetic powder in the working chamber will link in a link
state under the action of the magnetic flux generated from the yoke
when the current pass the excitation coil. The magnetic powder
clutch can transfer torque relying on the shear force generated
from magnetic chain and the friction generated from the magnetic
powder and working face. In this situation, the magnetic powder
clutch is in the combination state.
When the current is cut off, the magnetic flux will disappear along
with the disappearance of the magnetizing current, the magnetic
powder will be in the state of loose under the action of gravity
again, and will be thrown on the inner wall of active rotor under
the action of the centrifugal force.
In this case, the magnetic powder clutch will be in the state of
separation again.
The magnetic powder clutch and brake have the same principle, the
magnetic powder brake will form as long as driven rotor of the
magnetic powder clutch is fixed.
Single Shaft Power Brake data sheet as below:
| Item | Torque | Voltage | Speed | Max current | D1 | D2 | D3 | L1 | L2 | L3 | L4 | 6-S | d | t | R-diammeter | Deepth | Net weight |
| TZ6A-1 | 6 | 24 | 1400 | 0.8 | 130 | 62 | 44 | 25 | 10 | 67 | 107 | M5 | 12 | 4 | M4 | 8 | 3 |
| TZ12A-1 | 12 | 24 | 1400 | 1 | 157 | 62 | 50 | 30 | 15 | 84 | 133 | M5 | 16 | 5 | M4 | 8 | 5 |
| TZ25A-1 | 25 | 24 | 1400 | 1.5 | 182 | 78 | 58 | 40 | 19 | 91 | 154 | M6 | 20 | 6 | M5 | 10 | 7.5 |
| TZ50A-1 | 50 | 24 | 1400 | 1.8 | 219 | 100 | 75 | 50 | 22 | 110 | 185 | M6 | 25 | 8 | M6 | 12 | 13 |
| TZ100A-1 | 100 | 24 | 1000 | 2 | 290 | 120 | 90 | 65 | 25 | 143 | 238 | M8 | 30 | 8 | M10 | 20 | 28 |
| TZ200A-1 | 200 | 24 | 1000 | 3 | 335 | 140 | 110 | 70 | 30 | 170 | 275 | M10 | 35 | 10 | M10 | 20 | 47 |
| TZ400A-1 | 400 | 24 | 1000 | 4 | 398 | 200 | 130 | 99 | 35 | 199 | 338 | M12 | 45 | 14 | M10 | 20 | 73 |
FAQ
1. When can I get the quotation?
We usually quoted within 12 hours after receiving your inquiry. If
you are very urgent to get the price, please call us or tell us in
your email, so that we can regard your inquiry priority.
2. How should I place the order?
Please let us know the model number based on our specs for tension
controller,web guiding system. For powder clutch, powder brake,
please show us your drawing, or let us know your request torque,
and then we will provide you suitable model for confirmation.
3. What’s your MOQ basis?
Normally, we don’t have MOQ request.
4. What about the lead time for production?
Honestly, it depends on the order quantity and the type of our
products. For tension controller, load cell and edge position
controller which is about 1-3 days. For powder clutch, powder brake
which need about 3-5days.
5. What is the term of delivery?
We can arrange with EXW, FOB, CIF…etc. You can choose the most
convenient one or cost-effective way.
