Double Covoluted Industrial Air Springs for Firestone 2B310 Air Suspension Bags

Double Covoluted Industrial Air Spring for Firestone 2B310 Air Suspension Bags

Production Description : DOUBLE CONVOLUTED AIR SPRING FOR FIRESTONE 2B310

OE No: 2B310

Car Make : For truck 

Condition: Brand New
 

Position : Front

Warranty: 1 year

Model No.: 2B310

Product Photo:

Air Spring

Air springs are the only load support product that provide BOTH leveling capacity and improved ride comfort. Only air springs give you load support that is adjustable for your specific load. Add air when riding loaded to ensure your vehicle is level for a safer, more comfortable ride. Deflate the air springs when riding unloaded for optimal ride quality.

The Benefits of Air Spring

1. Eliminate Squat

Is the rear end of your vehicle sitting low from a heavy load? This is called squat or sag. Lift it back up where it belongs and enjoy the benefits listed below. This is especially beneficial while towing: adjust the air springs to accept the tongue weight of the trailer.

2. Reduce Poor Braking and Steering

The two front tires bear the majority of braking and steering. Air spring ensures that weight is properly distributed to all four tires for optimal braking and steering.

3. Eliminate Rough Ride

Progressive rate air springs significantly improve ride quality by better absorbing road inputs, while keeping your tires on the road for better handling.

4. Eliminate Poor Headlight Aim

Your headlights should be on the road and not in the trees. Only level and stable vehicles provide safe and proper headlight aiming—critical for safe night driving.

We also supply other Car Parts Air Spring

Warning and Tips

Maintenance of the air springs, Vehicle Check-List

•  Check the air lines and devices of leakage and that they turns freely.
•  Check the bellows bearing for damage, correct fastening, deformation, sharp edges.
•  Check the shock absorbers for operation and impermeability as well as tightness and bearing.
•  Periodically, check nuts and bolts for proper torque. For specific recommendations see manufacturer's manual.
•  Check axle suspension, trailing arms and rods for wear. 
•  Check height control valve to see that it is functioning properly. A properly maintained valve will save unneeded maintenance expense.
•  Routine inspection of all of the above according to manufacturer's instructions, will extend the life of your vehicle and reduce your overall maintenance expense. 

Air Spring Installation

1. Before you start installing air springs, make sure you have all the necessary tools and equipment to perform the repair safely.
2. Familiarize yourself with the suspension on which you are performing the repair by reviewing the manufacturers service guide.
3. If you are in doubt about something, ask for assistance from a qualified suspension specialist, the suspension manufacturer or the air spring manufacturer; This can save you a lot of time and aggravation later in the job.

Important tips to remember when installing a new unit

• Check levelling valve, linkage and transmission parts for wear and damage and if necessary replace the damaged parts.

• Check that the shock absorber for leakages and take a shock absorber test. A defective shock absorber must be replaced.

• Once the air lines are disconnected, check their entire length for cracks or other damage. Replace worn parts.

• With the air spring removed, other parts of the air suspension become more accessible. Check for wear or damage of the frame hangers, trailing arm bushings, torque rods, the trailing arms and the air spring mounts. When it is necessary, also replace parts.

• Check bearing for air spring bellow for external damage, deformation, sharp edges and correct fastening.

• Before installing the new unit, clean the air spring mounting plates to ensure proper attachment to the suspension.

• Always use new attaching bolts for the installation and observe the tightening torques. Never use old bolts, because these can fall out.

• Check the linkage of the levelling valve to see that it is functioning properly. Under load, the linkage should move from the neutral position up to the intake position. This lets air into the springs, which brings the arm back to the neutral position. This lets air into the springs, which brings the arm back to the neutral position. That opens the exhaust valve, allowing air to escape until the arm returns to the neutral position. Then check the driving level.

Company Information:

Company Certifie:

Our advantages:

Contact Us:

If you have any questions, pls do not hesitate to contact with me.Thank you so much.

Contact Name: Anita Huang

Tel:  86 020 36163613

Moblie: 0086 13501538820 (WhatsApp)

Skype:tmairsuspension_Andy.