Home Companies GANDO INTERNATIONAL (HONGKONG) LIMITED

Starting torque IP20 400VAC variable speed motor AC inverter drives for compressor

Active Member

Contact Us

Address: 701 of NO.69, xilinxili, siming, xiamen, China

Phone: 86-013-2436807

Contact name:

GANDO INTERNATIONAL (HONGKONG) LIMITED

Starting torque IP20 400VAC variable speed motor AC inverter drives for compressor

City & Province xiamen fujian

Product Details

400VAC Variable Speed AC Motor Inverter Drives for Compressor

A compressor is a mechanical device that takes in a medium and compresses it to a smaller volume. Compressors can either increase or decrease a given mass to a lower or higher pressure. A mechanical or electrical drive is typically connected to a pump that is used to compress the medium.

Compressors have many everyday uses, such as:

· Air conditioners,  (car,  home)

· Air pumps

· Home and industrial refrigeration

· High pressure car washes

· Hydraulic compressors for industrial machines

· Air compressors for industrial manufacturing

Compressors are used by many industries that depend on the power of compressed gas or fluid to power manufacturing processes of all kinds.

 

There are several different compressor types:

· Rotary screw compressor
Two helical rotors force gas into a chamber that decreases in size, thereby increasing the pressure of the gas. The screws in the rotary screw compressor can be lubricated with oil or non-lubricated. Oil-free compressors are used for gas that must remain clean and uncontaminated. Rotary screw compressors are typically sized from 30-200 horsepower.

· Reciprocating compressor
One or more pistons are moved inside a cylinder to increase the gas pressure. This is similar to a combustion engine without the ignition of fuel. Just like a car, the pistons generate much heat so the reciprocating compressor is typically cooled by air or water. Multi-stage reciprocating compressors pass the compressed gas from one cylinder to another, increasing the pressure in each stage. Most industrial compressors are multi-stage, ranging from one to 500 or more horsepower.

· Centrifugal compressor
Centrifugal compressors speed up and compress gas via a rotor with blades. Centrifugal force is used to force the air or gas to an outer chamber under higher pressure. Centrifugal compressors are designed to operate above 75-80% speed. Surging can occur below these speeds. This makes the centrifugal compressor ideal for continuous high duty operation.

 

Application Challenges

· Varied compressor I/O that must interface with the AC drive to control compressor functions.

· Reduce energy consumption

· Constant pressure regulation

· Constant torque load requirement

· Starting torque

 

Features of G7 series matching compressor application

Features

Benefits

PID Control Mode

Automatically regulate speed based on load conditions. The drive employs a built-in PID Controller (an external PID device is not required).

Flux Vector Control

With vector control, the system can operate at a stable speed regardless of the load.

Energy saving control

V/F pattern selection saves energy while operating with light load and low speeds.

Restart after momentary power loss

The motor continues running even after a 2 second momentary power loss.

Avoid mechanical resonance

The drive skips over the frequency at which resonance occurs.

Frequency Lower Limit

Continuous motor operation at low speed with a minimum speed reference

Reverse Prohibit

The drive can be prohibited from running in reverse by using the Reverse Prohibit Function.

 

Power range of G7 VFD

Voltage: 400VAC (380VAC – 460VAC)

Power: 22kw/30HP – 1000kw/1250HP

 

Specification of G7 VFD

Item

Specification

Input frequency

50/60Hz

Output frequency

0-400Hz

Overload current

150% rated current 1min.

Control mode

Close-loop vector control,  sensor-less vector control,  V/F control

Starting torque

150% 1hz (with PG 0hz)

Control precision

±0.2% (With PG ±0.02%)

Torque precision

±5%

Setting frequency resolution

Digital command 0.01hz; analog command 0.03hz/60hz

Output frequency resolution

0.01Hz

Frequency setting signal

-10V~+10V;0~+10V(20kΩ);4~20mA

Protection function

Over voltage, under voltage, over load, relay, overheat speed stall, grounding, instant power cut compensation( within 2 sec for operation mode. Continue to operate after the power is available), Charging protection( not to display when the dc voltage of main circuit is less than 50v)

Enclosure

IP20

Cooling mode

forced air cooling

Vibration

Less than 0.2g for 20hz

Ambient temperature / Humidity

-10 Degrees~+40 Degrees / 20~90%Rh (no condensation)

 

Tips:

A variable-frequency drive (VFD) is a system for controlling the rotational speed of an alternating current (AC) electric motor by controlling the frequency of the electrical power supplied to the motor. A variable frequency drive is a specific type of adjustable-speed drive. Variable-frequency drives are also known as adjustable-frequency drives (AFD), variable-speed drives (VSD), AC drives, microdrives or inverter drives. Since the voltage is varied along with frequency, these are sometimes also called VVVF (variable voltage variable frequency) drives.
 

Hot Products

400VAC Variable Speed AC Motor Inverter Drives for Compressor A compressor is a mechanical device ...
AC Variable Frequency Inverter Drives VFD for Screw Feeder 400V Screw feeders are used in various ...
22kw – 1000kw Variable Frequency AC Inverter Drives for Conveyor Conveyors are used in a broad range ...
1000kw / 1250HP AC Variable Frequency Inverter Drives for Metalforming Metalforming is the process ...
400V Variable Frequency AC VFD Drives for Decanter Centrifuge Decanter centrifuges are used to ...
AC Vector Control Motor Drive Compressor for Air Conditioners A compressor is a mechanical device ...